Garmin GPSMAP 5208 - Marine GPS Receiver Kurulum Talimatları Kılavuzu - Sayfa 19

Deniz GPS Sistemi Garmin GPSMAP 5208 - Marine GPS Receiver için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 5208 - Marine GPS Receiver 25 sayfaları. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Ayrıca Garmin GPSMAP 5208 - Marine GPS Receiver için: Önemli Güvenlik Bilgileri (4 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Kullanıcı El Kitabı (2 sayfalar), Kullanıcı El Kitabı (2 sayfalar), Teknik Referans (30 sayfalar), Kurulum Talimatları Kılavuzu (19 sayfalar), Kurulum Talimatları Kılavuzu (25 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Uygunluk Beyanı (1 sayfalar), Baskı Kılavuzu (2 sayfalar), Ek Kılavuz (24 sayfalar), Kullanıcı Kılavuzu (6 sayfalar)

Sayfayı Yazdır
Garmin GPSMAP 5208 - Marine GPS Receiver Kurulum Talimatları Kılavuzu
Wiring to a GPS 17 or GPS 17 HVS Antenna
If you already have a Garmin GPS 17 or GPS 17 HVS installed on your boat, you can wire it to the GPSMAP 4000/5000 series chartplotter
instead of installing the included GPS 17x. Wire the existing GPS 17 or GPS 17 HVS antenna to the included 19-pin NMEA 0183 cable as well
as to the power supply for the boat, referring to the diagram below. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183
cable or GPS 17 HVS cable. Solder all connections and seal them with heat-shrink tubing.
NOTE: If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS
antenna. The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network.
Garmin
GPSMAP 4000/5000 series
chartplotter
The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL (Phase Alternate Line) composite
video sources, and PC monitor output (4008/4208/4010/4210/5008/5208 = VGA output, 4012/4212/5012/5212/5015/5215 = XGA output).
Marine Video inputs are only available on the chartplotter to which they are attached and will not transmit over the Garmin Marine Network.
and
VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from two separate NTSC/PAL compatible video devices, such as VCR,
➊
➋
DVD, TV, or a video camera. The chartplotter can display one video input at a time or alternate between the two. See the owner's manual for
details. Sound from a video source must be attached to a separate stereo/audio system. The video output from video devices attaches to the
Video 1 (Black Cable) or Video 2 (Gray Cable) RCA connectors.
Use the PC monitor output (HD 15-pin) connector for remote viewing of the chartplotter display on a computer monitor. The remote monitor
➌
must be capable of at least VGA resolution and have multi-sync capability.
➌
➋
➊
GPSMAP 4000/5000 Series Installation Instructions
7.5 A - 42 V
PoWEr
CABLE
nMEA 0183
CABLE
Wiring to a GPS 17 or GPS 17 HVS Antenna
Marine Video Cable
PIn 1
PIn 2
PIn 17
Marine Video Cable
End View
+
BAttErY
WIrE
10–35 Vdc
CoLor
FuSE
rED (PoWEr)
BLACk (GnD)
orAnGE (ACC. on)
GrEEn (DAtA out)
>
GrEEn/WHItE (DAtA In)
>
note
Connector
rCA-1
➊
CEntEr
rCA-1 outEr
rCA-2
➋
CEntEr
rCA-2 outEr
HD-15 PIn 1
➌
HD-15 PIn 2
HD-15 PIn 3
PIn 7
HD-15 PIn 5
HD-15 PIn 6
HD-15 PIn 7
HD-15 PIn 8
HD-15 PIn 10
HD-15 PIn 13
HD-15 PIn 14
HD-15 PIn
SHELL
-
WIrE
CoLor
FuSE
1 A
rED (PoWEr)
BLACk (GnD)
YELLoW (on)
BLuE (DAtA In)
>
WHItE (DAtA out)
>
Pin
Function
2
VIDEo 1 In (BLACk jACkEt)
6
VIDEo 1 In, GnD
11
VIDEo 2 In (GrAY jACkEt)
15
VIDEo 2 In, GnD
1
VGA, AnALoG-rED
4
VGA, AnALoG-GrEEn
3
VGA, AnALoG-BLuE
13
VGA, AnALoG, GnD
8
VGA, AnALoG-rED, GnD
8
VGA, AnALoG-GrEEn, GnD
8
VGA, AnALoG-BLuE, GnD
13
VGA, SYnC-GnD
7
VGA, H-SYnC
12
VGA, V-SYnC
9
VGA, oVErALL SHIELD
GPS 17 or
GPS 17 HVS
antenna
19