Garmin GPSMAP 8700 Kurulum Talimatları Kılavuzu - Sayfa 5
Deniz GPS Sistemi Garmin GPSMAP 8700 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 8700 8 sayfaları.
Ayrıca Garmin GPSMAP 8700 için: Kurulum Talimatları Kılavuzu (6 sayfalar), Kurulum Talimatları Kılavuzu (27 sayfalar)
Sayfayı Yazdır
Item Description
Power source
Power cable
Horn
Lamp
NMEA 0183 cable
Relay (100 mA coil current)
Toggle switches to enable and disable lamp or horn alerts
Item
Wire Color
Red
Black
Yellow
J1939 Engine Network Connection Considerations
You must use a Garmin GPSMAP J1939 accessory cable when
connecting the chartplotter to the J1939 engine network to
prevent corrosion due to moisture. Using a different cable voids
your warranty.
If you have an existing engine network on your boat, it should
already be connected to power. Do not add any additional power
supply.
This chartplotter can connect to an engine network on your boat
to read data from compatible devices such as certain engines.
The engine network follows a standard and uses proprietary
messages.
You should connect only one chartplotter to one engine network.
Connecting more than one chartplotter to one engine network
may result in unexpected behavior.
The port labeled J1939 is used to connect the device to the
existing engine network. You must route the cable within 6 m
(20 ft.) of the engine network backbone.
The Garmin GPSMAP J1939 accessory cable requires
connection to a power source and proper termination. For more
information on connecting to your engine network, see the
manufacturer's engine documentation.
Pin
Wire Color
Bare
Red
Black
White
Blue
Wire Function
Power
Ground
Alarm
NOTICE
Description
Shield
Power, positive
Power, negative
CAN High
CAN Low
HDMI Video Considerations
To prevent corrosion due to moisture, you must use Garmin
GPSMAP accessory cables when connecting the chartplotter to
the video source or display. Do not connect a media player stick
directly into the back of the chartplotter. Using different cables or
connecting a media player stick into the back of the chartplotter
voids your warranty.
The GPSMAP 8700 chartplotter allows video input from HDMI
video sources, such as a Chromecast
protected HDMI content (HDCP content), though. Check the
video source's manual to verify that HDCP can be turned off for
the source.
HDMI video is shared across the Garmin Marine Network, but it
is not shared across the NMEA 2000 network.
Through the HDMI OUT port, you can display the video on
screen, such as a television or monitor.
The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft)
long. If you need a longer cable, you should use an active HDMI
cable only. You need an HDMI coupler to connect the two HDMI
cables.
You need a Garmin GPSMAP USB OTG adapter cable to power
a media player stick. The USB HOST port can supply up to
2.5 W to power a media player stick.
You must make all cable connections in a dry environment.
Devices
Item
Device
HDMI source, such as a Chromecast device
GPSMAP chartplotter
Monitor, such as a computer or television
Connections
From
To
HDMI source's HDMI
Chartplotter's HDMI IN
OUT port
port
Chartplotter's HDMI
Monitor's HDMI IN
OUT port
port
Chartplotter's USB OTG
HDMI source's USB
or USB HOST port
HOST port
Composite Video Considerations
This chartplotter allows video input from composite video
sources using the port labeled CVBS IN. When connecting
composite video, you should observe these considerations.
• The CVBS IN port uses a BNC connector. You can use a
BNC to RCA adapter to connect a composite-video source
with RCA connectors to the CVBS IN port.
• Video is shared across the Garmin Marine Network, but it is
not shared across the NMEA 2000 network.
NOTICE
device. You cannot view
™
Cable
Garmin HDMI Cable
Garmin HDMI Cable
GPSMAP USB OTG
adapter cable to
power the HDMI
source, if possible
(2.5 W maximum)
5