Garmin FUSION XS Series Kurulum Talimatları - Sayfa 2
Denizcilik Ekipmanları Garmin FUSION XS Series için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Garmin FUSION XS Series 4 sayfaları. Marine wake tower speakers
Ayrıca Garmin FUSION XS Series için: Kurulum Talimatları Kılavuzu (13 sayfalar), Kurulum Talimatları Kılavuzu (11 sayfalar), Kurulum Talimatları Kılavuzu (6 sayfalar), Kurulum Talimatları Kılavuzu (6 sayfalar)
Sayfayı Yazdır
Pipe Mount
Bracket for
Fusion·
XS Series Marine
Wake Tower Speakers
Installation Instructions
Important Safety Information
'
.,.,., ",---=~J:•
,
:.~;_..~:,,:~A
.: ........ ..._...,, .. __
See the Important Safety and Product
Information guide in the product box for
product warnings and other important
information.
This device. must be installed according to
these instructions.
Disconnect the vehicle's or vessel's power
supply before beginning to install this
device.
&CAUTION
Continuous exposure to sound pressure
levels over 100 dBA may cause permanent
hearing loss. The volume is typically too
loud if you cannot hear people speaking
around you. Limit the amount of time you
listen at high volume. If you experience
ringing in your ears or muffled speech, stop
listening and have your hearing checked.
To avoid possible personal injury, always
wear safety goggles, ear protection, and a
dust mask when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what
is
on
the opposite side of the surface to
avoid damaging the vessel.
It is strongly recommended that you have
your audio system installed by a
professional installer to ensure optimum
performance.
You must read all installation instructions
before beginning the installation. If you
experience difficulty during the installation,
go to www.fusionentertainment.com for
product support.
What's In
the Box
Two wake tower pipe brackets
Four short hex screws and washers for
securing the brackets to the speakers
•
Four long hex screws and washers for
securing the brackets to the wake tower
pipe
Tools
Needed
Drill and 12 mm
(½
in.) drill bit
•
4 mm and 5 mm hex drivers or hex keys
Wire strippers
•
Solder and heat-shrink tubing for wire
connections
NOTE: For customized installations,
additional tools and materials may be
needed.
Mounting the Bracket
You can mount Fusion XS Series Marine
Wake Tower speakers (sold separately) to a
2
wake tower pipe using the included
brackets.
When installing the speaker and bracket,
you can route the speaker and LED cable
either along the outside of the wake tower
pipe or inside it.
NOTE: If you route the speaker wire inside
the wake tower pipe, you should install a
grommet or other protective covering (not
included) around the hole in the pipe to
protect the wire when routing it through the
hole.
1 If necessary, mark the locations on the
wake tower pipe where you plan to
mount the speakers.
2 If you plan to route the cable through the
wake tower pipe, drill 12 mm (
1 /
2
in.)
cable pass-through holes in the bottom
of the wake tower pipe.
3 If you plan to route the cable through the
wake tower pipe, install grommets or
other protective coverinqs (not included}
around the holes you drilled in the
previous step (optional}.
4 If necessary, route extended speaker
Md LED wires (not included) to the
mounting locations, either along the
outside of the wake tower pipe or inside
it.
5
Feed the cable
G)
from the speaker
through the base of the bracket®·
5 4
~ 2
6 Place the base of the bracket over the
mounting knob on the speaker@.
7 Using a 4 mm hex driver or hex key,
attach the collar© to the base of the
bracket using the two shorter screws
and washers®, but do not fully tighten
them.
8 Using the installation instructions
provided with the Fusion XS Series
Marine Wake Tower speakers, connect
the speaker wires and LED wires.
9 Feed the connected wires through the
pass-through hole into the wake tower
pipe®, or place them in the channel on
the base of the bracket
(l).
Installation Instructions