Garmin GHP 10V Kurulum Talimatları Kılavuzu - Sayfa 11
Denizcilik Ekipmanları Garmin GHP 10V için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GHP 10V 20 sayfaları. Marine autopilot system
Ayrıca Garmin GHP 10V için: Kurulum Talimatları Kılavuzu (48 sayfalar), Kullanıcı El Kitabı (28 sayfalar), Kurulum Talimatları Kılavuzu (20 sayfalar)
Sayfayı Yazdır
Configuring the GHP 10V
The GHP 10V must be configured and tuned to your boat dynamics
and motor configuration. Use the Sea Trial Wizard on the GHC 10
to configure the GHP 10V. These wizards will walk you through the
necessary configuration steps.
about the Sea trial Wizard
The Sea Trial Wizard configures the fundamental sensors on the
autopilot, and it is extremely important to complete the wizard in
conditions appropriate for your boat.
Important Sea trial Wizard Considerations
Complete the Sea Trial Wizard in calm water. The nature of calm water
is relative to the size and shape of your boat.
• Ensure your boat does not rock while sitting still or moving very
slowly.
• Ensure your boat is not significantly affected by the wind.
• Keep the weight on your boat balanced. DO NOT move around
on the boat while completing any of the steps in the Sea Trial
Wizard.
Starting the Sea trial Wizard
Before you start the Sea Trial Wizard, you must drive to an open area of
calm water.
1. Turn on the GHP 10V.
2. Select an option:
• If the Sea Trial Wizard starts automatically, proceed to step 3.
• If the Sea Trial Wizard does not start automatically, select Menu
> Setup > Dealer Autopilot Configuration > Wizards > Sea
Trial Wizard.
3. Select Begin.
Performing the Sea trial Wizard
1. Drive your boat to an open area of calm water.
2. Start the Sea Trial Wizard
3. Configure the planing RPM
4. Calibrate the compass
(page
5. Perform the autotune procedure
6. Set north
(page
11).
7. If necessary, set the fine heading adjustment
Configuring the Planing RPM
1. Note the RPM reading from the tachometer on the dashboard of
your boat at the point your boat transitions from displacement to
planing speed.
2. If the tachometer value does not match the value on the GHC 10,
use the arrows to adjust the value.
3. Select Done.
Calibrating the Compass
1. Drive your boat at slow/idle speed in a straight line.
2. Select Begin, and continue to drive in a straight line.
3. When instructed, turn the boat slowly clockwise, taking care to
make the turn as steady and flat as possible.
Turn slowly so that the boat DOES NOT list.
The GHC 10 displays a completion message when the calibration is
complete.
GHP 10V Installation Instructions
(page
11).
(page
11).
11).
(page
11).
(page
11).
4. Select an option:
• If the calibration completes successfully, select Done.
• If the calibration fails, select Retry and repeat steps 1–3.
Performing the autotune Procedure
Before you can perform the autotune procedure, you must have a large
stretch of open water available.
1. Adjust the throttle so the boat travels below planing speed.
2. Select Begin.
The boat performs a number of zigzag motions while the Autotuning
is in progress.
The GHC 10 displays a completion message.
3. Select an option:
• If the autotune completed successfully, select Done and take
manual control of the boat.
• If the autotune failed, adjust the throttle and select Retry
Autotune.
4. If autotune fails, repeat steps 1–3 until the autotune completes
successfully.
5. If the autotune procedure continues to fail after you reach maximum
cruising speed, reduce your speed to the initial autotune speed
and select Alternate Autotune to begin an alternate autotuning
procedure.
Setting north
Before you can set north, you must have at least 45 seconds of hazard-
free, open water available.
This procedure appears only if you connect an optional GPS device to
the GHP 10V
(page
10), and the device has acquired a GPS position. If
you do not have a GPS device connected, you are prompted to set the
fine heading adjustment
(page
1. Drive the boat in a straight line at cruising speed, and select Begin.
The GHC 10 displays a completion message when the calibration is
compete.
2. Select an option:
• If the calibration completed successfully, select Done.
• If the calibration failed, repeat steps 1–2.
Setting the Fine Heading adjustment
This procedure appears only if you do not have an optional GPS device
connected to the GHP 10V
(page
installed on your boat that has acquired a GPS position, are prompted to
set north instead
(page
11).
1. Using a handheld compass, identify north.
2. Adjust the fine heading setting until it matches north on the
magnetic compass.
3. Select Done.
Evaluating the Results of the autopilot
Configuration
1. Test the autopilot at a slow speed.
2. If necessary, adjust the gain setting
3. Test the autopilot at a higher speed (normal operating conditions).
4. If necessary, adjust the gain and acceleration limiter settings.
11).
10). If you do have a GPS device
(page
12).
11