Garmin GPSMAP 7215 Kurulum Talimatları Kılavuzu - Sayfa 15
Denizcilik Ekipmanları Garmin GPSMAP 7215 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 7215 21 sayfaları. Flush mount template
Ayrıca Garmin GPSMAP 7215 için: Kullanıcı El Kitabı (2 sayfalar), Teknik Referans (42 sayfalar), Uygunluk Beyanı (6 sayfalar), Ek Kılavuz (24 sayfalar), Şablon Kılavuzu (2 sayfalar)
Sayfayı Yazdır
Wiring to a Lamp or to a Horn (optional)
The GPSMAP 6000/7000 series chartplotter can be used with a lamp, a horn, or both, to sound or flash an alert when the chartplotter displays a
message. The alarm does not need to be wired for the GPSMAP 6000/7000 chartplotter to function. The alarm circuit switches to a low-voltage
state when the alarm sounds. The maximum current is 100 mA, and a relay is needed to limit the current from the chartplotter to 100 mA. To
manually toggle visual and audible alerts, install single-pole, single-throw switches.
GPSMAP 6000/7000 series
chartplotter
Wiring to a DB-9 PC Serial Connector
The GPSMAP 6000/7000 series chartplotters can be connected to a PC with a serial port by wiring the chartplotter to a DB-9 serial connector.
Garmin
GPSMAP 6000/7000 series
chartplotter
Wiring to a GPS 17 or GPS 17 HvS Antenna
If you already have a Garmin GPS 17 or GPS 17 HVS installed on your boat, you can wire it to the GPSMAP 6000/7000 series chartplotter
instead of installing the included GPS 17x. Wire the existing GPS 17 or GPS 17 HVS antenna to the included 19-pin NMEA 0183 cable as well
as to the power supply for the boat, referring to the diagram below. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183
cable or GPS 17 HVS cable. Solder all connections and seal them with heat-shrink tubing.
Note: If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS
antenna. The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network.
Garmin
GPSMAP 6000/7000 series
chartplotter
GPSMAP 6000/7000 Series Installation Instructions
Garmin
Wiring to a Lamp, a Horn, or Both
PoWER
CABLE
NMEA 0183
CABLE
Wiring to a DB-9 Serial PC Connector
PoWER
CABLE
NMEA 0183
CABLE
Wiring to a GPS 17 or GPS 17 HvS Antenna
WIRE
CoLoR
FuSE
7.5 A - 42 v
RED (PoWER)
BLACk (GND)
PoWER
CABLE
NMEA 0183
YELLoW (ALARM)
CABLE
+
BAttERY
10–35 vdc
WIRE
SEE tABLE FoR
WIRE CoLoRS
FuSE
7.5 A - 42 v
RED (PoWER)
BLACk (PWR GND)
BLACk (DAtA GND)
RX / B(-)
>
RX / A(+)
>
tX / A(+)
>
tX / B(-)
>
uNCoNNECtED
+
BAttERY
WIRE
10–35 vdc
CoLoR
FuSE
7.5 A - 42 v
RED (PoWER)
BLACk (GND)
oRANGE (ACC. oN)
GREEN (DAtA out)
>
GREEN/WHItE (DAtA IN)
>
+
-
BAttERY
10–35 vdc
HoRN
RELAY
100 mA MAX
CoIL CuRRENt
-
DB-9 PIN
NuMBERS
PIN 5: GND
PIN 3: tX
>
PIN 2: RX
>
-
WIRE
CoLoR
FuSE
1 A
RED (PoWER)
BLACk (GND)
YELLoW (oN)
BLuE (DAtA IN)
>
WHItE (DAtA out)
>
LAMP
DB-9 serial
PC connector
6
2
7
3
8
4
9
5
End view
GPS 17 or
GPS 17 HVS
antenna
15