Garmin Reactor 40 Kicker Yapılandırma Kılavuzu - Sayfa 2
Denizcilik Ekipmanları Garmin Reactor 40 Kicker için çevrimiçi göz atın veya pdf Yapılandırma Kılavuzu indirin. Garmin Reactor 40 Kicker 6 sayfaları.
Ayrıca Garmin Reactor 40 Kicker için: Kurulum Talimatları Kılavuzu (29 sayfalar), Yapılandırma Kılavuzu (8 sayfalar)
Sayfayı Yazdır
Reviewing the Results of the Dockside Wizard
The values you chose when you ran the Dockside Wizard are
displayed.
1
Examine the results of the Dockside Wizard.
2
Select any incorrect value.
3
Correct the value.
4
Repeat steps 2 and 3 for all incorrect values.
5
When you are finished reviewing the values, select Done.
Disabling the Shadow Drive Valve
After you complete the Dockside Wizard, you must disable the
Shadow Drive valve in the settings. This autopilot system is not
compatible with the Shadow Drive valve, and an error message
appears until you disable it.
Select an option:
• On a helm control, from the heading screen, select Menu
> Setup > User Autopilot Setup > Shadow Drive.
• On a chartplotter, select Settings > My Vessel >
Autopilot Installation Setup > Shadow Drive.
The Shadow Drive field shows a status of Disabled.
Sea Trial Wizard
The Sea Trial Wizard configures the fundamental sensors on the
autopilot, and it is extremely important to complete the wizard in
conditions appropriate for your boat.
Important Sea Trial Wizard Considerations
The Sea Trial Wizard must be completed in calm water.
Because the nature of calm water is relative to the size and
shape of the boat, before you begin the Sea Trial Wizard, the
boat must be in an appropriate location.
• The boat must not rock while sitting still or moving very
slowly.
• The boat must not be significantly affected by the wind.
While completing the Sea Trial Wizard, observe these
considerations.
• Weight on the boat must remain balanced. While completing
any of the steps in the Sea Trial Wizard, do not move around
on the boat.
Performing the Sea Trial Wizard
1
Drive your boat to an open area of calm water.
2
Select an option:
• On a helm control, select Menu > Setup > Dealer
Autopilot Setup > Wizards > Sea Trial Wizard.
• On a chartplotter, select Settings > My Vessel >
Autopilot Installation Setup > Wizards > Sea Trial
Wizard > Begin.
3
If necessary, enter the maximum speed of the boat when
powered by the kicker motor only.
4
Calibrate the compass
5
Perform the Autotune procedure
Procedure, page
2).
6
Set north
(Setting North, page
adjustment
(Setting the Fine Heading Adjustment, page
Calibrating the Compass
1
Select an option:
• If you are performing this procedure as part of the Sea
Trial Wizard, select Begin.
• If you are performing this procedure outside of the Sea
Trial Wizard on a helm control, from the heading screen,
select Menu > Setup > Dealer Autopilot Setup >
Compass Setup > Calibrate Compass > Begin.
2
(Calibrating the Compass, page
(Performing the Autotune
3), or set the fine heading
• If you are performing this procedure outside of the Sea
Trial Wizard on a chartplotter, select Settings > My
Vessel > Autopilot Installation Setup > Compass
Setup > Compass Cal. > Begin.
2
Follow the directions until calibration is complete, taking care
to keep the boat as steady and flat as possible.
The boat should not list during calibration. Make sure one
side of the vessel is not loaded more heavily than the other.
3
Select an option:
• If the calibration completes successfully on a helm control,
select Done.
• If the calibration completes successfully, on a chartplotter
select OK.
• If the calibration is not successful, select Retry and repeat
steps 1 through 3.
When the calibration is complete, a magnetic environment
quality value is shown. A value of 100 indicates the CCU was
installed in a perfect magnetic environment and calibrated
correctly. If this value is low, you might need to relocate the
CCU and calibrate the compass again.
Performing the Autotune Procedure
Before you can begin this procedure, you must have a large
stretch of open water available.
1
Engage the kicker motor in forward gear at moderate speed.
2
Steer the boat by hand and point in a direction with at least
100 to 200 m (100 to 200 yd.) of open water.
3
Select an option:
• If you are performing this procedure as part of the Sea
Trial Wizard, select Begin.
• If you are performing this procedure outside of the Sea
Trial Wizard on a helm control, from the heading screen,
select Menu > Setup > Dealer Autopilot Setup >
Autopilot Tuning > Autotune > Begin.
• If you are performing this procedure outside of the Sea
Trial Wizard on a chartplotter, select Settings > My
Vessel > Autopilot Installation Setup > Autopilot
Tuning > Autotune > Begin.
The boat performs various zigzag motions while the Autotune
is in progress.
4
After the procedure is finished, follow the on-screen
instructions.
5
If the Autotune procedure is not successful, select an option:
• If the Autotune procedure is not successful and you have
not reached maximum cruising speed, increase the speed,
select Run Normal Autotune on a helm control or Run
Standard Autotune on a chartplotter, and repeat steps 1
through 3 until the Autotune procedure completes
successfully.
• If the Autotune procedure is not successful and you have
reached maximum cruising speed, reduce your speed to
2).
the initial Autotune speed, and select Run Alternate
Autotune to begin an alternate procedure.
• If the Autotune fails immediately and you are traveling in
a circle instead of performing zigzag motions, select
3).
Reverse Steering Dir. > Run Normal Autotune on a
helm control or Switch Direction > Run Standard
Autotune on a chartplotter, and repeat steps 1 through 3
until the Autotune procedure completes successfully.
When the Autotune procedure is complete, gain values are
displayed. You can use these values to determine the quality of
the Autotune procedure.
Autotune Gain Values
After the Autotune procedure is complete, you can review the
gain values provided on the helm control. You can record these
numbers for reference if you want to run the autotune procedure