Garmin Delta Kullanıcı El Kitabı - Sayfa 6
Evcil Hayvan Bakım Ürünü Garmin Delta için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin Delta 12 sayfaları. Delta series
Ayrıca Garmin Delta için: Kullanıcı El Kitabı (10 sayfalar)
Sayfayı Yazdır
3
Plug the other end of the power cable into an appropriate
power source.
Charging the Dog Collar Device
To prevent corrosion, thoroughly dry the contacts on the collar
and the surrounding area before connecting the charging clip.
Before you put the collar on the dog, remove the charging clip. If
you do not remove the clip, it may become detached from the
collar and become lost.
You should fully charge the battery before you use the device
for the first time. Charging a fully depleted battery takes about
two hours. The device will not charge when outside the
temperature range of 32° to 104°F (0° to 40°C).
1
Snap the charging clip
2
Plug the small end of the power cable into the mini-USB port
on the charging clip.
3
Plug the other end of the power cable into a power source.
The status LED is solid red when the collar is charging.
4
After the status LED turns solid green, remove the charging
clip from the collar.
Turning On the Devices
• On the handheld device, hold
on.
• On the dog collar device, hold
and the collar beeps twice.
Turning Off the Devices
• On the handheld device, hold
off.
• On the collar, hold
until the status LED flashes and the
collar beeps once.
Dog Collar Devices
You can use up to three dog collar devices with a single
handheld device. You can select a different training mode and
intensity level for each dog collar device.
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a color on the handheld device.
indicates the selected color.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are paired from the
factory using the black color selection.
1
Turn on the dog collar device and the handheld device.
2
NOTICE
onto the device.
until the LCD display turns
until the status LED flashes
until the LCD display turns
2
On the handheld device, select
indicates the selected color.
3
On the handheld device, select an intensity level greater than
0
(page
3).
4
On the dog collar device, hold the power key for about two
seconds.
The device beeps once when you press the button and again
after two seconds.
5
After the second beep, on the handheld device, select a
training key.
The dog collar device turns off and beeps to indicate whether
the devices paired successfully.
Short beep
Devices paired successfully
Long beep
Devices did not pair
TIP: If the devices did not pair successfully, you should verify
the batteries in both devices are fully charged and the intensity
level is set higher than 0.
Selecting a Dog Collar Device
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device
Select
to choose the color.
indicates the selected color.
The training keys control the dog collar device associated with
the selected color.
Dog Training
You should research and investigate the training methods best
suited for you, your dog, and your needs. This manual provides
some basic guidelines for training, but each dog has unique
training needs.
When used properly, the Delta training system is a very
effective training tool to aid your dog in reaching its full potential.
The use of the training system should be part of an overall
training program.
Begin training your dog on a leash, without the Delta training
system. You should train your dog how to heel, sit, and come to
you. After the dog understands these three basic commands,
you can begin training with the dog collar device and the leash.
Finally, when the dog consistently obeys commands using the
leash and collar, you may be able to remove the leash to train
with only the dog collar device.
Fitting the Collar on Your Dog
To prevent irritation from the contact points, remove the collar
for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to
use on any person.
Before you put the collar on the dog, remove the charging clip. If
you do not remove the clip, it may become detached from the
collar and become lost.
In order to properly correct the dog, the collar and device must
fit the dog properly. If the collar is too loose or positioned
incorrectly, corrections may be inconsistent. This can delay or
prevent successful training.
1
Place the collar around the middle of the dog's neck.
2
Position the device at the front of the dog's neck, with the
status LED facing toward the dog's chin and the contact
points against the throat.
to choose the color.
(page
CAUTION
NOTICE
Dog Training
2).