Brother DCP 585CW - Color Inkjet - All-in-One Hızlı Kurulum Kılavuzu - Sayfa 30
Hepsi Bir Arada Yazıcı Brother DCP 585CW - Color Inkjet - All-in-One için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Brother DCP 585CW - Color Inkjet - All-in-One 45 sayfaları. Quick setup guide - spanish
Ayrıca Brother DCP 585CW - Color Inkjet - All-in-One için: (İngilizce) Hızlı Yapılandırma Kılavuzu (43 sayfalar)
Sayfayı Yazdır
For Wireless Network Users
13
Configure the wireless
settings using the
automatic wireless
(one-push) method
a
Confirm your wireless router or access point
has the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ symbol as shown below.
b
Place the Brother machine within range of a
SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your access
point/router.
c
Push the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ button on your wireless
router or access point.
See the user's guide for your wireless router or
access point for instructions.
d
On your machine, press Menu.
Press a or b to choose Network and press
OK.
Press a or b to choose WLAN and press OK.
Press a or b to choose SES/WPS/AOSS and
press OK.
When Network I/F switched to
Wireless is displayed, press OK to accept.
This will start the wireless setup wizard.
To cancel, press Clear/Back.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™) your access point uses to
configure your machine.
Note
If your wireless access point supports Wi-Fi
Protected Setup™ (PIN Method) and you want to
configure your machine using the PIN (Personal
Identification Number) Method, see Using the PIN
Method of Wi-Fi Protected Setup™ in the Network
User's Guide on the CD-ROM.
30
e
If the LCD shows Connected, the machine
has successfully connected to your router or
access point. You can now use your machine
in a wireless network.
If the LCD shows Setting WLAN,
Connecting SES (Connecting WPS or
Connecting AOSS), then
Connection Failed, the machine has not
successfully connected to your router or
access point. Try starting from c again. If the
same message is indicated again, reset the
machine back to the default factory settings
and try again. For resetting, see Restore the
network settings to factory default on page 43.
If the LCD shows Setting WLAN, then
Connection Failed or Incorrect Mode,
a session overlap or connection failure was
detected. (see the table below), the machine
has detected 2 or more routers or access
points on your network that have the
SecureEasySetup™, Wi-Fi Protected Setup™
mode or AOSS™ mode enabled. Make sure
that only one router or access point has the
SecureEasySetup™, Wi-Fi Protected Setup™
mode or AOSS™ mode enabled and try
starting from c again.
LCD messages when using the
SES/WPS/AOSS control panel menu
Searching or accessing the
Setting WLAN
access point and downloading
settings from the access point.
Connecting to the access
Connecting
point.
SES/WPS/AOSS
Connection failed. If this is
Connection
shown after the LCD shows
Failed
Connecting
SES/WPS/AOSS, a session
overlap was detected.
A session overlap was
Incorrect
detected.
Mode
The machine has successfully
Connected
connected.
Note
If you encounter a problem during setup,
temporarily place your machine closer to the
wireless access point, and go back to c.
Wireless setup is now complete.