Brother P-touch 1280 Kullanıcı Kılavuzu

Etiket makinesi Brother P-touch 1280 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Brother P-touch 1280 2 sayfaları. Electronic labeling system
Ayrıca Brother P-touch 1280 için: Kullanıcı Kılavuzu (2 sayfalar), (İngilizce) Kullanıcı Kılavuzu (1 sayfalar)

Sayfayı Yazdır

USER'S GUIDE

www.brother.com

LN7629001

Printed in China

INTRODUCTION

With your PT-1280, you can create labels for any application. Select from the

many frames, character sizes and styles to design beautiful custom labels. In

addition, the variety of tape cartridges available allows you to print labels with

different widths and exciting colours.

Read this manual carefully before starting and keep the manual in a handy

place for future reference.

GENERAL PRECAUTIONS

• Use only Brother TZ tapes with this machine. Do not use tapes that do

not have the

mark.

• Do not clean the machine with alcohol or other organic solvents. Only use

a soft, dry cloth.

• Do not touch the print head mechanism. Use a soft wipe (e.g. a cotton

swab) when cleaning the print head.

• To avoid injuries, do not touch the cutter's edge.

• To prevent damage or breakage of the glass, do not press hard on the LCD

display.

• Do not put any foreign objects into or heavy objects on the machine.

• Do not leave any rubber or vinyl on the machine for an extended period of

time, otherwise the machine may be stained.

• Do not get the machine wet, such as by touching with wet hands or spilling

beverages on to the machine.

• Do not expose the machine to extremely high temperatures or high

humidity. Never leave it on the dashboard, in the back of your car, near

heaters or other hot appliances. Keep it out of both direct sunlight and rain.

• Avoid using the machine in extremely dusty places.

• Do not pull on the tape being fed from the P-touch, otherwise the tape

cassette may be damaged.

• Do not attempt to cut the tape while printing or feeding since this will

damage the tape.

• Do not try to print labels using an empty tape cassette set in the P-touch.

Doing so will damage the print head.

• Remove the batteries and disconnect the AC adaptor if you do not intend

to use the machine for an extended period of time. (Note: When power is

disconnected for more than three minutes, all text shown in the display and

any text files stored in the memory will be lost. Language and unit settings

will also be cleared.)

• Do not use old and new batteries together or mix alkaline batteries with

other type batteries, or set the positive and negative end in the wrong

position. Otherwise, the batteries may leak or be damaged.

• Use only the suggested AC adaptor for this machine to prevent any

damage or failure.

PREPARATION

Power Supply & Tape Cassettes

Make sure that the power is turned off when replacing batteries or tape cassette.

Open the back cover by pressing in the rough area at the top end of the

machine.

If a tape cassette is already

installed, remove it by pulling it

straight up. Also, if batteries are

already installed, remove them.

Print head

Tape cutter lever

Insert six new AAA-size alkaline batteries (LR03), making sure that their

poles point in the correct directions. Always replace all six batteries at the

same time using brand new ones.

Insert a tape cassette, making sure that it snaps into place.

End of tape

Toothed Wheel

Cutter's edge

Tape guide

Tape exit slot

• Make sure that the end of the tape feeds under the tape guides.

• If the ink ribbon is loose, use your finger to wind the toothed wheel in the

direction of the arrow on the cassette.

• Use only Brother TZ tapes with this machine.

Securely close the back cover, making sure that it snaps into place.

After you have installed the tape,

feed the tape (see Feeding)

once and then push in the tape

cutter lever to cut the tape.

When using optional AC adaptor (model

AD-5000)

Insert the plug on the adaptor cord into

the adaptor jack on the top end of the

machine.

Insert the plug into the nearest standard

electrical outlet.

For memory back up, we recommend using

AAA-size alkaline batteries (LR03) together

when using the AC adaptor.

OPERATION

Keyboard & LCD

Width

Size

Style

Cursor

Underline/Frame

Caps

Label Length

Print key

Power key

Cursor key

Function key

Preview key

OK key

Favourite keys

ESC key

Character key

Backspace key

Tab key

Enter key

Caps key

Shift key

Symbol key

Accent key

Auto Format key

Space key

• The LCD shows one row of 15 characters; however, the text that

you enter can be up to 80 characters in length.

• Use Cursor key while holding down Shift key to go to beginning/

end of the text.

Initial Setting

Start your machine

Supply power by using six AAA batteries or the optional AC adaptor, and then

press

Set the language (English/Spanish/French/Portuguese)

Choose a language with

and press

Set the unit (inch/mm)

Choose a unit with

and press

• The machine automatically turns off if no key is pressed within 5

minutes.

• To cancel operations, press

• To initialize the settings, turn off the machine and then while

holding down

and

, press

to turn the machine back on.

Finally, release

and

Creating Labels

See the reverse side for steps of creating labels.

[GETTING STARTED]

REFERENCE

Troubleshooting

Error message

Message

Cause/Remedy

Battery Weak!

The batteries are weak.

Check Battery!

The installed batteries are about to run out.

Invalid!

• There is no text above the cursor when you set Number-

ing.

• Invalid character is selected for Numbering.

• Invalid number is selected for Tab Length or Label Length.

No Text!

• You tried to print a text file when there is no data stored in

the memory.

• The Print key is pressed when no text is entered.

• You tried to set Copies, Numbering or Mirror when no text

is entered.

Line Limit!

• You tried to enter a 3rd line by pressing Enter key.

• You tried to print a 2 line text when 3.5 mm or 6 mm tape is

installed.

No Cassette!

You tried to print a label when there is no cassette installed.

Cutter Error!

Tape cutter lever is used in the middle of printing process.

Full!

The maximum number of characters (80 characters) have

already been entered.

Text Too Long!

The text length exceeds the selected label length or the

selected Auto Format setting length.

No Frame OK?

Printing on 3.5 mm tape with invalid Frame setting ON.

(Select

to print with no Frame,

to cancel.)

What to do when...

Problem

Solution

The display stays blank

• Check that the batteries are correctly inserted.

after you have turned on

• If the batteries are weak, replace them.

the machine.

• Check that the suggested adaptor is correctly connected.

The machine does not

• Check that the tape cassette has been inserted correctly.

print, or the printed

• If the tape cassette is empty, replace it.

characters are blurred.

The printed characters

• The batteries may be weak. Replace them.

are not formed properly.

The memory has

• The batteries may be weak. Replace them.

cleared on its own.

A blank horizontal line

• There may be some dust on the print head. Remove the

appears through the

tape cassette and use a dry cotton swab to gently wipe the

printed label.

print head with an up-and-down motion.

• The print head can be cleaned more easily if the optional

print head cleaning cassette (TZ-CL3) is used.

The machine has

• Turn off the machine, and then while holding

"locked up" (i.e., nothing

down

and

, press

to turn the machine back on.

happens when a key is

Finally, release

and

pressed, even though

• Note: The text and formats in the display and all text files

the machine is on).

stored in the memory are erased. Also, the language and

unit settings will be cleared.

Specifications

Item

Specification

160 mm (W) × 151 mm (D) × 60 mm (H)

Dimensions

Weight

470 g (without batteries and tape cassette)

Power supply

Six AAA-size alkaline batteries (LR03 : not included) or

optional AC adaptor (model AD-5000)

Tape cassette

Brother TZ tape (width) :

3.5 mm, 6 mm, 9 mm, 12 mm

Accessories

(Supplies may differ by distribution.)

Accessories

Stock No.

Tape Cassettes

See the attached TZ Tape Catalogue.

AC adaptor

model AD-5000

Cutter Unit

TC-5 (replacement)

If the cutter blade becomes blunt after repetitive use and the tape cannot be

cut cleanly, replace with new cutter unit (stock no. TC-5) by obtaining from an

authorised brother reseller.

Be sure to use scissors to cut the fabric tapes. The built-in cutter can-

not completely cut the fabric tapes.