Brother P-touch PT-D610BT Hızlı Başlangıç Kılavuzu - Sayfa 7
Etiket makinesi Brother P-touch PT-D610BT için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Brother P-touch PT-D610BT 9 sayfaları.
Ayrıca Brother P-touch PT-D610BT için: Manuel (9 sayfalar), Manuel (9 sayfalar)
Sayfayı Yazdır
Error Messages
Message
Cause/Remedy
Incorrect no. of digits
The number of digits entered in the barcode data does not match
the number of digits set in the barcode parameters. Enter the correct
number of digits.
Cutter malfunction
If the tape is jammed in the Cutter unit, remove the tape. Turn the
Label Printer off and then on again before continuing.
Label too long
The printed label length using the text entered is longer than 999 mm.
Edit the text so that the label length is less than 999 mm.
Text too long
The printed label length using the text entered is longer than the length
setting. Edit the text to fit within the set length or change the length
setting.
System error XX
Contact Brother customer service.
Troubleshooting
If you need additional help, visit support.brother.com.
Problem
Solution
The Label Printer
• Check that the Tape Cassette is inserted correctly.
does not print.
• If the Tape Cassette is empty, replace it. To order supplies and
accessories, visit www.brother.com.
• Check that the Tape Cassette Compartment Cover is securely
closed.
• Check that the Label Printer is on.
• Check that the computer's or mobile device's Bluetooth setting is on.
• Check that the Label Printer is connected to your computer or mobile
device via Bluetooth.
• Check that the Label Printer is selected in the Brother iPrint&Label
app.
• Check that the Label Printer is not paired with another device.
• Make sure the Label Printer and your mobile device or computer are
close enough to communicate.
Troubleshooting (cont.)
Problem
Solution
The Label Printer does not
• Check that the automatic Bluetooth re-connection setting of
print.
another computer or mobile device is not enabled.
• Make sure no devices that emit radio waves (for example,
a microwave oven) are located nearby.
• Check that the correct printer driver is installed when printing from
a Windows computer.
• Connect the Label Printer to your computer using the USB Cable
(included) when printing from a computer.
• If the Print Head is dirty, clean it with a cotton swab or with the
optional Print Head Cleaning Cassette (TZe-CL4).
• The tape does not feed
• If the tape is bent, cut off the bent section with scissors.
correctly.
• If the tape is jammed, remove the Tape Cassette, remove the
• The tape gets stuck
jammed tape, and then cut off any damaged tape with scissors.
inside the Label Printer.
• Check that the end of the tape exits through the Tape Guide.
• Confirm that the tape is pointed at the Tape Exit Slot.
• Remove the Tape Cassette and insert it again.
An error occurred when
Go to your mobile application's settings menu and select Support
using a mobile app.
page > FAQs & Troubleshooting.
The screen is locked, or
See the Basic Operations section in this guide and reset the
the Label Printer does not
Label Printer's internal memory to the factory settings. If resetting
operate normally.
the Label Printer does not solve the problem, disconnect the AC
Adapter and remove the batteries for more than 10 minutes.
The LCD remains blank
Check that the batteries are correctly installed or that the AC
after turning the power on.
Adapter included with your Label Printer is correctly connected.
The Label Printer stops
• Replace the Tape Cassette if striped tape is visible as this
while printing a label.
indicates that you have reached the end of the tape.
• Replace all batteries or connect the AC Adapter directly to the
Label Printer.