Fujitsu fi-6770 Series Kullanıcı Kılavuzu - Sayfa 6
Tarayıcı Fujitsu fi-6770 Series için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Fujitsu fi-6770 Series 26 sayfaları. Image scanner
Ayrıca Fujitsu fi-6770 Series için: Kurulum Prosedürleri Kılavuzu (6 sayfalar), Broşür (2 sayfalar), Başlangıç Kılavuzu (14 sayfalar), Başlangıç Kılavuzu (26 sayfalar), Sarf Malzemesi Değiştirme ve Temizleme Talimatları (22 sayfalar)
Sayfayı Yazdır
Unplug the scanner when a trouble
occurs.
Immediately unplug the scanner when a trouble
occurs.
Never cut the ground connection until the scanner
is unplugged from the Power outlet.
Do not disassemble the scanner.
Do not take apart or modify the scanner. The
inside of the scanner contains high-voltage compo-
nents.
Touching these components might cause electric
shock or fire.
Do not use aerosol or alcohol sprays
near the scanner.
Do not use any flammable substance or alcohol
based cleaning sprays (such as aerosol sprays) to
clean the scanner.
Sparks, caused by static electricity, generated
when blowing off dust and dirt from the outside of
the scanner, may cause a fire.
Do not place the scanner within the
reach of small children.
To avoid injuries, do not place the scanner in an
area where small children may be able to reach.
Do not touch the heated section for a
long time.
Do not touch the heated section such as the
bottom of the scanner for a long time.
Doing so may cause a low-temperature burn on
your skin.
Do not cover the scanner with
something during its operation.
Do not use the scanner while covered with a
blanket, etc. Doing so may raise the temperature
inside and cause a fire.
Do not use the scanner where it gets
wet.
Do not use the scanner at a place such as a
bathroom, shower room, or swimming pool where
it may easily get wet. Doing so might cause electric
shock or fire.
6
AUTION
The following are important cautions described in this manual
Do not install the scanner on an
unstable work table.
When installing the scanner on a work table, make
sure that the table is flat and level. Place the
scanner so that none of its parts extend beyond
the edge of the table.
Also, it must be strong enough to support the
weights of the scanner and other devices.
Firmly insert the power plug.
Firmly insert the power plug into the Power outlet
as far it can go.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of the
scanner, which may result in fire or scanner
failure.
Do not place heavy objects or stand
on the top of the scanner.
Do not place heavy objects on the scanner or
stand on its top to perform other work.
Doing so might cause injuries and equipment
failure.
Do not use the scanner immediately
after moving it from a cold place into
a warm room.
Do not use the scanner immediately after moving it
from a cold place into a warm room.
Condensation may occur, which might lead to
scanning errors. Let the scanner dry for one or two
hours before you use it.
Before moving the scanner, discon-
nect the power plug from the Power
outlet.
Do not move the scanner with the power and inter-
face cables connected as this can damage the
cables, which can later cause fire, electric shock
as well as injuries.
Before moving the scanner, be sure to disconnect
the power plug from the Power outlet, and all other
interface cables. Make sure that the floor is free of
any obstructions.
Protect the scanner from static
electricity.
Install the scanner away from strong magnetic
fields and other sources of electronic noise. Also,
protect the scanner against any static electricity,
which can cause the scanner to malfunc-
tion.Choose a static-free place to install the
scanner.
Avoid any contact when scanner is in
use.
Avoid getting a sleeve, necktie, or hair caught up
in any scanner mechanism during scanning since
this may cause injuries.