Installation
S T E P
The rack rail (bracket) needs to be attached to the rack and the ETERNUS DX60/DX80 mounted.
1. Adjust the rack rail (bracket)
size to fit the rack.
"L" is stamped on the inner
side of the left rack rail.
[Left]
(Front rack pillars)
2. Attach the rack rails (brackets) to the rack. The size of the
ETERNUS DX60/DX80 is 2U.
Tighten the screws in the same locations on both the front and rear sides of the rack pillars
3rd position
(M5 screws)
1st position
(M5 screws)
Cable Connection
S T E P
Various cables need to be connected to the rear of the
ETERNUS DX60/DX80.
Point
IMPORTANT
LAN Cables
Rear view
The RMT port is on the left side, and MNT port
is on the right side.
The MNT port must always be connected. The
RMT port only needs to be connected when the remote
support connection is to be independent of the customer
network.
"4.2.1 LAN Cable Connection (For Operation Management)" in the
"User Guide"
Fibre Channel Cables
Rear view
The left port is 0, and right port is 1.
Connect a Fibre Channel cable to each CM port.
"4.2.2 Fibre Channel Cable Connection (For Fibre Channel) " in the "User
Guide"
(Rear rack pillars)
Loosen the screws,
and adjust the rack rails to
the depth of the rack.
"R" is stamped on the inner
side of the right rack rail.
[Right]
[Screw location of the rack rail (bracket)]
[Left]
2U
ETERNUS DX60/DX80
Base line of the
ETERNUS DX60/DX80
Rack rail (bracket)
To help with cable management and prevent
incorrect connection, attach labels to the cables
and note where each cable is connected to and
from.
The cables should never be bent, twisted or
pulled.
Controller
Enclosure
Controller
Enclosure
3. Mount the ETERNUS DX60/DX80 in the rack.
IMPORTANT
[Right]
4. Fasten the ETERNUS DX60/DX80 to the rack.
3rd position
(M5 screws)
1st position
(M5 screws)
MiniSAS Cables
When Drive Enclosures are installed, miniSAS cables are
used to connect between the SAS ports of the enclosures.
Connect the Controller Enclosure to Drive Enclosure 1, Drive
Enclosure 1 to Drive Enclosure 2, Drive Enclosure 2 to Drive
Enclosure 3, etc. The number of Drive Enclosure can be
checked with the "DE_No." label.
Example for connection of miniSAS cable
(when two Drive Enclosures are installed)
Rear view
Cable
underside in the SAS (OUT) port.
Insert the connector with a
SAS (IN) port.
Power Cords
Cable
Use release ties to hold the power cords in place.
Rear view
●
Make sure to install or remove the enclosure
to or from the rack by two or more people.
●
Multiple Drive Enclosures must be connected
to the controller enclosure following the order
of the "DE_No. label" numbers attached to
each Drive Enclosure. The position of the
labels are in the positions shown below.
At the right side of the front of
the drive enclosure
DE_No. label
"3.2 Rack Installation" in the "User Guide"
The SAS (OUT) port is on the left side,
and SAS (IN) port is on the right side.
Insert the connector with a
mark on its underside in the
"4.2.5 MiniSAS Cable Connection (For Drive Enclosures)" in the "User
Guide"
"4.2.6 Power Cord Connection" in the"User Guide"
Between the EXP#0 and
EXP#1 expanders at the rear
of the drive enclosure
Cable
Underside of
the SAS (OUT) side plug
Drive
Enclosure
Underside of
Drive
the SAS (IN) side plug
Enclosure
Controller
Enclosure
mark on its
Cord
Drive
Enclosure
Controller
Enclosure
Sayfayı Yazdır