Indesit I6T52/AUS Kullanım Talimatları Kılavuzu - Sayfa 6

Fırın Indesit I6T52/AUS için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Indesit I6T52/AUS 20 sayfaları.

Sayfayı Yazdır

1. Control Panel

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used, and

the fuse cover re-fitted. If the fuse cover is lost, the

plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

! For appliances with a rating greater than 13 amp (eg:

electric hob, double ovens and freestanding electric

cookers etc.) the mains cable must be wired into a

cooker output point with a rating of 45 amp. In this

case the cable is not supplied.

Disconnecting the cable

Ensure that the means for disconnection of the

power cable is incorporated into the fixed wiring in

accordance with local wiring rules.

(New Zealand statutory warning): The cooker must be

connected to the electricity supply by a cable fitted

with an appropriately rated plug that is compatible with

the socket-outlet fitted to the final subcircuit in the fixed

wiring that is intended to supply this cooker.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket. Instructions for

connecting cable to an alternative plug:

! The wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue

- Neutral

Brown

- Live

If the colours of the wires in the mains lead do not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked "E" or or

coloured Green or Green & Yellow.

Connect Brown wire to terminal marked "L" or coloured

Red.

Connect Blue wire to terminal marked "N" or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a

13 amp fuse. A 15 amp plug must be protected by a 15

amp fuse, either in the plug or adaptor or at the distribution

board. If you are in any doubt about the electrical supply

to your machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE

"NEUTRAL" ("N")

GREEN &

YELLOW

BROWN

13 amp fuse

BROWN

"LIVE" ("L")

CROSS-BAR

BLUE

GREEN AND YELLOW

CORD GRIP

"EARTH" ("E")

Disposing of the appliance

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the plug

body and dispose of it as described above.

Checking the connection for leaks

Upon completion of installation, check the gas circuit, the

internal connections and the taps for leaks using a soapy

solution (never a flame). Also check that the connecting

pipe cannot come into contact with moving parts which

could damage or crush it. Make sure that the natural gas

pipe is adequate for a sufficient supply to the appliance

when all the burners are lit.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).