Indesit I5GMH6AG Kullanım Talimatları Kılavuzu - Sayfa 7

Ocaklar Indesit I5GMH6AG için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Indesit I5GMH6AG 28 sayfaları. Cooker and oven

Sayfayı Yazdır

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will

be fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled

or if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (see below).

Connecting a flexible jointless stainless steel pipe

to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and does

not come into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using

a 7 mm socket spanner (see

fi gure), and replace them with

nozzles suited to the new type

of gas (see Burner and nozzle

specifi cations table).

3. Replace all the components

by following the above

instructions in reverse.

Adjusting the hob burners' minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the

position of the knob from minimum to maximum and

vice versa several times, checking that the flame is not

extinguished.

! The hob burners do not require primary air

adjustment.

! After adjusting the appliance so it may be used with

a different type of gas, replace the old rating label with

a new one that corresponds to the new type of gas

(these labels are available from Authorised Technical

Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating to

"regulators for channelled gas".

Safety Chain

The cooker is fitted with a safety chain to be fixed by

means of a screw (not supplied with the cooker) to

the wall behind the appliance, at the same height as

the chain is attached to the appliance.

Choose the screw and the screw anchor according

to the type of material of the wall behind the applian-

ce. If the head of the screw has a diameter smaller

than 9mm, a washer should be used. Concrete wall

requires the screw of at least 8mm of diameter, and

60mm of length.

Ensure that the chain is fixed to the rear wall of the

cooker and to the wall, as shown in figure, so that

after installation it is tensioned and parallel to the

ground level.

! In order

to prevent

accidental

tipping of the

appliance, for

example by

a child clim-

bing onto the

oven door, the

supplied safety

chain MUST be

installed!