Indesit ITL50GM Kullanım Talimatları Kılavuzu - Sayfa 12

Ocaklar Indesit ITL50GM için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Indesit ITL50GM 24 sayfaları. Indesit it50g s; it50g1 s; it50l s; it50g1; it50l; it50g; itl50g1; itl50gm; itl50ga; itl50gw 50cm free standing gas cooker

Sayfayı Yazdır

Indesit ITL50GM Kullanım Talimatları Kılavuzu

Use of Hotplates

Practical Advice on Using the Burners

To use the burners as efficiently as possible, some

basic guidelines should be followed:

• Use cookware that is the right size for each burner

(see table) in order to prevent the flame from

spreading beyond the bottom of the cookware.

• Only use cookware with flat bottoms.

• As soon as the boiling point is reached, turn the

knob to the lowest setting.

• Always use lids with pots and pans.

Burner

Fast (R)

Semi Fast (S)

Auxiliary (A)

! On models equipped with a reduction grid, the grid

should only be used with the auxiliary burner when

cookware with a diameter of less than 12 cm is used.

1. Press the ignition button and then push in and turn

the control knob of the chosen burner anti-clockwise

to the large flame symbol. Continue to press the

ignition button until the sparks light the gas.

2. Turn the control knob anti-clockwise to the desired

setting. Only turn the control knob between the

large flame symbol and the small flame symbol for

adjusting the setting.

3. To turn off, turn the control knob fully clockwise to

the symbol O.

DO NOT use the hotplate unless all pan supports

are in position.

DO NOT use mis-shapen pans which may be

unstable.

DO NOT use round base woks directly on the pan

supports.

DO NOT use the glass lid (if fitted) as a working

surface.

WARNING! The glass lid can

break in if it is heated up. Turn

off all the burners and the

electric plates before closing

the lid. *Applies to the models

with glass cover only.

Cookware diameter (cm)

24 - 26

16 - 20

10 - 14

Each burner is fitted with a spark ignitor for lighting

the gas. To ensure rapid lighting of the burners every

time they are used, the ignitors must be kept clean and

dry. Remove any food spillage or cleaning materials

from the electrode using a small nylon brush such as a

tooth brush. Access to the electrode can be achieved

by lifting off the loose burner parts carefully when the

burners are cool.

When the hotplate burner bodies and caps are

removed for cleaning, be careful not to drop any food

particles or cleaning materials into the burner bases, to

avoid the possibility of blocking the gas jets.

If aluminium based pans are used, a silvery deposit

may appear on the top edge of the pan support

fingers. See ‚Care and Cleaning' section for cleaning

information.

SAFETY REQUIREMENTS FOR DEEP FAT FRYING

1. Never fill chip pans more than one third full with oil

or fat.

2. Never leave oil or fat unattended during the heating

or cooling period.

3. Never heat fat or fry with a lid on the pan.

4. Always dry food thoroughly before frying, and

lower it slowly into the hot oil or fat. Frozen foods in

particular will cause frothing and spitting if added

too quickly.

5. Always keep the outside of the pan clean and free

from streaks of oil or fat.

HOW TO DEAL WITH A FAT FIRE

1. Do not move the pan.

2. Turn off the hotplate burners.

3. Smother the flames with a fire blanket or damp

cloth to extinguish the fire. Do not use water or a

fire extinguisher as the force of it may spread the

burning fat or oil over the edge of the pan.

4. Leave the pan for at least 60 minutes before moving

it.