Kohler K-1257 Kurulum Kılavuzu - Sayfa 5

Banyo Armatürleri Kohler K-1257 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Kohler K-1257 48 sayfaları. Bath whirlpool
Ayrıca Kohler K-1257 için: Ev Sahibi El Kitabı (32 sayfalar), Ev Sahibi El Kitabı (29 sayfalar), Kurulum Kılavuzu (48 sayfalar), Ev Sahibi El Kitabı (36 sayfalar), Ev Sahibi El Kitabı (32 sayfalar), Kurulum Kılavuzu (48 sayfalar), Kaba İnşaat Kılavuzu (4 sayfalar), Kaba İnşaat Kılavuzu (4 sayfalar), Kaba İnşaat Kılavuzu (4 sayfalar), Kurulum Kılavuzu (44 sayfalar), Kurulum Kılavuzu (48 sayfalar), Kurulum Kılavuzu (44 sayfalar), Ev Sahibi El Kitabı (29 sayfalar), Kaba İnşaat Kılavuzu (4 sayfalar), Kurulum Kılavuzu (48 sayfalar)

Sayfayı Yazdır

Position

the rough

plumbing.

Construct 2x4 or

2x6 stud framing

according to the

roughing-in

information.

Provide a 1/16" (2 mm)

gap between the bath rim

and framing.

1. Prepare the Site

NOTICE: Unless otherwise speciﬁed, ﬂoor support under the whirlpool must provide for a minimum of

80 lbs/square foot (390 kg/square meter) loading.

NOTICE: Do not support the whirlpool by the rim.

Make sure the ﬂooring offers adequate support for your whirlpool, and verify that the subﬂoor is

ﬂat and level.

The whirlpool should be installed in a drop-in installation. Construct 2x4 or 2x6 stud framing

designed for your particular installation. Provide for a 1/16" (2 mm) gap between the bottom of the

whirlpool rim and the stud framing. Frame the ﬂoor, or construct a frame for a raised installation in

accordance with the roughing-in information packed with the whirlpool.

Carefully lay out and cut the rough deck material. Use the cut-out template if one is provided, or

refer to the roughing-in cut-out information.

Position the plumbing according to the roughing-in information packed. Cap the supplies, and

check for leaks.

2. Prepare the Whirlpool

Install the drain to the whirlpool according to the drain manufacturer's instructions. Do not connect

the trap at this time.

Position a clean drop cloth or similar material in the bottom of the whirlpool. Be careful not to

scratch the surface of the whirlpool.

3. Disconnect the Pump

NOTE: No cutting of the whirlpool harness (piping) is required for this installation. Any cutting of the

harness will void the warranty.

Disconnect the pump and in-line heater (if equipped) from the shipping location by cutting the two

banding straps with tin snips.

Move the pump and in-line heater (if equipped) aside.

Relocate the pump and heater (if equipped) next to the customized inlet/outlet connections of the

whirlpool harness. The pump may protrude beyond the rim of the bath. See the rough-in details.

Kohler Co.

Frame the floor

according to the

roughing-in information.

Verify that the subfloor

offers adequate support,

and is flat and level.

Cut the pump

banding straps.

1055820-2-A