AAxeon FCU-3002SX Kullanıcı Kılavuzu

Medya Dönüştürücü AAxeon FCU-3002SX için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AAxeon FCU-3002SX 2 sayfaları. Gigabit smart diagnostic media converter

Sayfayı Yazdır

Trademarks

Contents subject to revision without prior notice.

All trademarks remain the property of their owners.

This publication may not be reproduced as a whole or in

part, in any way whatsoever unless prior consent has been

obtained from owner.

FCC Warning

The OPTOLINX Gigabit Media Converter has been tested

and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These

standards are designed to provide reasonable protection

against harmful interference when this device is operated

in a commercial environment. This device generate, use,

and can radiate radio frequency energy and may cause

harmful interference to radio communications unless

installed in accordance with this User's Guide. Operation

of this device in a residential area is likely to cause

harmful interference in which cases the user is

responsible for taking appropriate remedial action at

his/her own expense.

CE Mark Warning

This is class A products. In a domestic environment this

product may cause radio interference in which case the

user will need to consider adequate preventative

methods.

1. Checklist

The carton should contain the following items:

OPTOLINX Gigabit Media Converter

AC-DC Power Adapter

User's guide

Please notify your sales representative immediately if any

items are missing or damaged.

2. Overview

The OPTOLINX Gigabit Media Converter is designed to

meet the massive needs for Gigabit network deployment.

This solution allows users to extend a copper based

Gigabit network via fiber cable to a maximum distance up

to 30KM.

The OPTOLINX Gigabit Media Converter is fully compliant

with IEEE802.3z & 802.3ab standards. It can be installed

into a FCU-RACK Converter Chassis. The installation &

operation procedures are simple & straightforward.

Operation status can be locally monitored through a set of

Diagnostic LED located in the front panel.

Features

1000Base-T to 1000BASE-SX/LX Converter

Standard : IEEE 802.3z & 802.3ab

Interface: 1 * RJ-45 connector

1 * SC Duplex connector or

1 * SC Simplex connector (W2 type)

MDI/MDIX Auto-Crossover supported

LED:

Power , FDX , TP Link, FO Link ,

TP ACT, FO ACT

Plug-and-Play installation

Supports Link Alarm

Supports Jumbo Frame (64-9216 Byte)

Supports Voltage Monitor

3. Installation

•

Attach fiber cable from the OPTOLINX Gigabit Media

Converter to the fiber network. The fiber connections

must be matched – transmit socket to receive socket.

•

Attach a UTP cable from the 1000BASE-T network to

the RJ-45 port on the OPTOLINX Gigabit Media

Converter

•

Connect the power adapter to the OPTOLINX Gigabit

Media Converter and check that the Power LED lights

up. The TX Link and FX Link LEDs will light up when all

the cable connections are satisfactory.

•

Dip-switch select :

Default is set to OFF from PIN 1 to PIN 4

Pin 1 Off/On Always OFF

Pin 2 Off/On Always OFF

Pin 3 Off/On FX Force Mode

FX Auto-Negotiation

Pin 4 Off/On Link Alarm Disable

Link Alarm Enable

FO TP

Link

ACT

FDX PWR

Fig. 1 Gigabit Ethernet Converter Front Panel

5VDC IN

Fig. 2 Gigabit Ethernet Converter Rear Panel

PN: 6304X3002100XXX

OFF