Avocent Emerge MPX Hızlı Kurulum Kılavuzu
Genişletici Avocent Emerge MPX için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Avocent Emerge MPX 2 sayfaları. Hd extender
Sayfayı Yazdır
QUICK INSTALLATION GUIDE
For manual downloads, visit:
www.avocent.com/manuals
The following instructions will help you
install your extender system. For more
detailed instructions, including wired
installations and fi rmware updates, refer to
the installer/user guide.
Should you require further assistance,
please contact Avocent Technical Support.
Overview
Emerge MPX extenders broadcast high defi nition
computer graphics or video, audio and control
data from a source device to multiple receivers.
1
Preparation
Place your MPX transmitter, access points,
and receivers at least 3 feet apart on a stable
work surface and attach the antennas. If your
installation includes access points or receivers
that will have a wired IP connection, connect
the L2 LAN port of the transmitter to the L1 LAN
port on each access point or receiver. Attach
the transmitter and access points to their power
supplies and appropriate power sources and
wait for transmitter initialization to complete: the
2 green LEDs will alternate and other LEDs will
turn off.
Transmitter Confi guration
2
Connect a browser client to the transmitter's L1
LAN connector and launch a browser session
using the IP address 192.168.1.1 with a subnet
mask of 255.255.255.0.
• At the login prompt, leave the username
blank and enter Admin (case sensitive) as the
password.
• When prompted, select the appropriate
country code.
• Select the Source Device Settings page
and confi gure the input video mode for the
transmitter.
- Auto (default) - auto-detects DVI-D/
HDMI sources; and RGB and component
To Contact Avocent Technical Support: Visit www.avocent.com
Avocent, the Avocent logo, and Emerge are registered trademarks of Avocent Corporation or its affi liates in the U.S. and other countries. All other marks are the property of their respective owners. ©2009 Avocent Corporation.
®
Emerge
MPX
HD Extender
Emerge MPX Family Confi gurations
Video
Source
Video
Source
Transmitter
sources with an Avocent-supplied adapter
or cable.
- Manual (HDMI/DVI) - HDMI or DVI
- Manual (RGB) - HD15 or DVI-A
- Manual (Component) - YPbPr.
• Select the Change Password page to update
the system password.
• Select the System Settings page to enter a
device name.
• If your installation includes access points
or wired receivers, select the Media LAN
Settings page and enable Wired Connection
in the Basic LAN Settings tab.
HD Access Point Confi guration
3
(optional)
In the Active Receivers list (lower left of the
transmitter's web page), click the MAC address
of the fi rst access point to access its web
interface. Apply the appropriate country code.
When the connection resumes, select the
System Settings page to enter a name for the
access point. To confi gure an access point to
MPX
MPX
Transmitter
Receiver
Up to 8 display confi guration
MPX
MPX
Access Point
Front
Back
Up to 64 display confi guration
Video
Display
Video
MPX
Display
Receiver
(Up to 8 per Access Point)
ignore all but the currently detected transmitter,
select the detected transmitter in the Bindings
page to move it into the Confi gured Transmitter
table. The connection will reset. Repeat for each
access point.
4
Explicit Bindings - Optional
Apply power to your receivers. Wait for them
to initialize and bind to the transmitter: the two
green LEDs cease to alternate.
• Select the transmitter/access point's Bindings
page and verify that all active receivers are
listed (by MAC address) in the Detected
Receivers list.
• Select the Add to Confi gured Receivers
checkbox next to each receiver then apply the
changes.
• Assign one unit as the Primary receiver for
exchange of IR, serial, and EDID data and
apply the change.
• If all receivers are bound, you may disable the
transmitter/access point from automatically
binding additional receivers.
590-973-501A