DG Technologies DPA XL Hızlı Başlangıç Kılavuzu - Sayfa 2
Teşhis Ekipmanları DG Technologies DPA XL için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. DG Technologies DPA XL 2 sayfaları.
Sayfayı YazdırB L U E TO OT H Q U I C K S TA R T G U I D E
1. Once the DPA XL drivers are installed on PC, plug-in the USB cable to the DPA XL, then
the USB cable to the PC. Wait to hear the familiar windows chime and for the DPA XL
Power LED to be a solid green. (Note: BT should not be used for ECU programming.)
⇨ DG Tech DPA XL ⇨ DPA XL Config Utility. Select "Yes" to pop-up message.
2. Go to
3. Select "Select Device".
4. Select "Configure Bluetooth Discovery".
5. Select "Enable".
6. Select "OK".
7. Select "Exit".
8. Select "Exit".
9. Select on "OK".
⇨
10. Go to
and select "Devices" (Note: Screens may vary depending on
Windows version & scale.)
11. Select "Bluetooth & other devices".
12. Select "Add Bluetooth or other devices"
13. Select "Bluetooth".
14. Wait for a moment for the "DPA XL..." device to appear and select it.
15. Connected! Select "Done" & close out of "Settings" screen.
16. Go back to the still-open Bluetooth window and select "Select Bluetooth Device"
17. From the drop-down menu, select the "DPA XL #xxxx-xxxx-xxxx" device, then select "OK".
(Note: Device ID can be confirmed by looking at the back of the DPA XL and the bar
code number. First 4 digits of the bar code do not apply.)
18. Notice the Device ID is now shown at the bottom of the dialog box. Select "Exit" OR to
enable "CyberGuard", continue below at Step 21.
Note: After any configuration changes, such as those shown above, and before connecting to DG
Diagnostics or an OEM application, disconnect ALL power from DPA XL for about 10 seconds, then repower
DPA XL.
What is CyberGuard in relation to Bluetooth?? If there are multiple Bluetooth compatible
devices (PC's, cellphones, etc.) in the area, for example, and you don't want your DPA XL to be
seen or "discovered" by those devices, you can do that thru the "Configure Bluetooth
Discovery" button. In the "Configure Bluetooth Discovery", you can "Enable" or "Disable" this
discovery.
To "Disable" Bluetooth discovery so your DPA XL can't be seen by other Bluetooth compatible
devices:
19. Ensure the USB cable is connected to the DPA XL and the PC.
⇨ DG Tech DPA XL ⇨ DPA XL Config Utility. Select "Yes" to pop-up message.
20. Go to
21. Select "Select Device".
22. Select "Configure Bluetooth Discovery".
23. Select "Disable"
24. Select "OK"
25. Select "Exit".
26. Select "Exit".
To "Enable" Bluetooth discovery so the DPA XL can be seen by other Bluetooth devices or be
"discovered" by those devices, follow steps 19-22 above, select "Enable" in step 23, then
follow remaining steps 24-26.
For configuring multiple PC's with multiple DPA XL's, see the full User Manual for additional
details.
Vehicle Network Solutions
248.888.2000 | [email protected]
www.dgtech.com
B L U E TO OT H Q U I C K S TA R T G U I D E
1. Once the DPA XL drivers are installed on PC, plug-in the USB cable to the DPA XL, then
the USB cable to the PC. Wait to hear the familiar windows chime and for the DPA XL
Power LED to be a solid green. (Note: BT should not be used for ECU programming.)
⇨ DG Tech DPA XL ⇨ DPA XL Config Utility. Select "Yes" to pop-up message.
2. Go to
3. Select "Select Device".
4. Select "Configure Bluetooth Discovery".
5. Select "Enable".
6. Select "OK".
7. Select "Exit".
8. Select "Exit".
9. Select on "OK".
⇨
10. Go to
and select "Devices" (Note: Screens may vary depending on
Windows version & scale.)
11. Select "Bluetooth & other devices".
12. Select "Add Bluetooth or other devices"
13. Select "Bluetooth".
14. Wait for a moment for the "DPA XL..." device to appear and select it.
15. Connected! Select "Done" & close out of "Settings" screen.
16. Go back to the still-open Bluetooth window and select "Select Bluetooth Device"
17. From the drop-down menu, select the "DPA XL #xxxx-xxxx-xxxx" device, then select "OK".
(Note: Device ID can be confirmed by looking at the back of the DPA XL and the bar
code number. First 4 digits of the bar code do not apply.)
18. Notice the Device ID is now shown at the bottom of the dialog box. Select "Exit" OR to
enable "CyberGuard", continue below at Step 21.
Note: After any configuration changes, such as those shown above, and before connecting to DG
Diagnostics or an OEM application, disconnect ALL power from DPA XL for about 10 seconds, then repower
DPA XL.
What is CyberGuard in relation to Bluetooth?? If there are multiple Bluetooth compatible
devices (PC's, cellphones, etc.) in the area, for example, and you don't want your DPA XL to be
seen or "discovered" by those devices, you can do that thru the "Configure Bluetooth
Discovery" button. In the "Configure Bluetooth Discovery", you can "Enable" or "Disable" this
discovery.
To "Disable" Bluetooth discovery so your DPA XL can't be seen by other Bluetooth compatible
devices:
19. Ensure the USB cable is connected to the DPA XL and the PC.
⇨ DG Tech DPA XL ⇨ DPA XL Config Utility. Select "Yes" to pop-up message.
20. Go to
21. Select "Select Device".
22. Select "Configure Bluetooth Discovery".
23. Select "Disable"
24. Select "OK"
25. Select "Exit".
26. Select "Exit".
To "Enable" Bluetooth discovery so the DPA XL can be seen by other Bluetooth devices or be
"discovered" by those devices, follow steps 19-22 above, select "Enable" in step 23, then
follow remaining steps 24-26.
For configuring multiple PC's with multiple DPA XL's, see the full User Manual for additional
details.
Vehicle Network Solutions
248.888.2000 | [email protected]
www.dgtech.com