Allied Telesis AT-8401 Kurulum Kılavuzu - Sayfa 2

Ağ Donanımı Allied Telesis AT-8401 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Allied Telesis AT-8401 2 sayfaları. Management fabric card

Sayfayı Yazdır

Secure the management card to the switch. Use a Phillips screwdriver to

tighten the two installation screws found on the faceplate of the management

card.

Note

Always use the installation screws to secure the management card to the

switch. Leaving a management card partially seated may cause the switch to

halt and subsequently crash.

For local management of the chassis, attach one end of a RS-232 cable with a

DB9 connector to the RS-232 port on the management card and the other end

of the cable to a terminal or PC with a terminal emulator program.

A T - 8

R S -2

T E R

M IN A

P O R

P W R

M G N

FA N

W A IT

R E M

O V E

R E S

E T

Make sure the PWR, FAN A, and FAN B LEDs on the front of the management

card are steady green. See the LEDs Section.

Attach a MAC Address sticker to the front of the chassis.

This sticker contains the MAC Address of the AT-8400 Management card. ATI

recommends attaching the sticker to the fan tray cover on the front of the

chassis.

Removing a Management Card

Before you remove an AT-8401 management card, you need to power down the

switch. To remove an AT-8401 Management Card, follow these steps:

Caution

Before removing a management card, refer to the AT-8400 Series Switch

Reference Guide for electrical safety and emission information.

Using a Phillips screwdriver, loosen the two installation screws on the

faceplate of the installed AT-8401 Management Card in slot M.

Caution

Be sure to observe all standard electrostatic discharge (ESD) precautions,

such as wearing an antistatic wrist strap, to avoid damaging the device. A

management card can be damaged by static electricity.

Pull the top and bottom locking levers out and away from the card as you slide

the card out of the chassis as shown in the following diagram.

4 0 1

Store the management card in an static-proof bag.

FL T

LEDs

M S TR

FA N

Refer to the table below for AT-8401 Management Card LED information.

LED

PWR

FLT

MGMT

MSTR

FAN A

FAN B

A T- 84

RS -23

TE RM

INA L

PO RT

PW R

FLT

MG NT

FA N

MS TR

WA IT/

FA N

RE MO

RE SE

State

Description

Steady Green

The management card is receiving power.

Steady Red

There is a system fault. This is an unrecoverable error.

Steady Green

Indicates a Power on Self Test (POST) has been

completed successfully.

Steady Amber

Indicates a POST is occurring. After one minute, indicates

a POST has failed.

Steady Green

Indicates the chassis is the master of an enhanced stack.

OFF

Indicates chassis is not a member of an enhanced stack.

Or, indicates the chassis is a member of an enhanced

stack, but it is a slave not a master. Check the

management console for details.

Steady Green

Fan A is operating correctly.

Steady Amber

Fan A is experiencing alarm conditions.

OFF

FAN A is not installed.

Steady Green

Fan B is operating correctly.

Steady Amber

Fan B is experiencing alarm conditions.

OFF

FAN B is not installed.

LED

State

WAIT/

Steady Green

REMOVE

Steady Amber

1. If the PWR LED remains off for more than 10 seconds, the management card is not receiving power.

RESET Button

The RESET button on the management card allows you to reset the chassis,

including the line cards. You may need to reset the management card after

upgrading the firmware. To reset the AT-8400 Chassis, locate the RESET button on

the front of the management card. Press the reset button with the tip of a pen.

Caution

Using the Reset button halts all network operations until the CPU returns to a

normal state.

Technical Specifications

Maximum Operating Temperature:

Maximum Storage Temperature:

Operating and Storage Altitude:

Relative Humidity Operating

and Storage:

Electrical Safety and Emission Statement

Standards: This product meets the following standards when installed in compliant host equipment.

RADIATED ENERGY

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to

Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to

operate this equipment.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

Emission

FCC Class A, EN55022 Class A, VCCI Class A, C-TICK

WARNING:

In a domestic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

Immunity

EN55024

Electrical Safety EN60825, EN60950 (TUV), UL60950 (UL/cUL)

No part of this publication may be reproduced without prior written permission from Allied Telesyn Inc.

Description

Indicates you can safely remove a line card from the

AT-8400 Chassis.

Indicates a disconnect request is being processed. You

cannot safely remove a line card from the AT-8400

Chassis while the LED is in this state.

0° C to 40° C (32° F to 104° F)

-20° C to 80° C (-4° F to 176° F)

Up to 3,048 meters (10,000 feet)

5% to 80% (non-condensing)

U.S. Federal Communications Commission

Industry Canada