Dell PowerVault DR4100 Qiuck Kurulumu

Depolama Dell PowerVault DR4100 için çevrimiçi göz atın veya pdf Qiuck Kurulumu indirin. Dell PowerVault DR4100 1 sayfaları. Backup and recovery appliance
Ayrıca Dell PowerVault DR4100 için: Başlangıç Kılavuzu (10 sayfalar), Manuel (37 sayfalar), Yayın Notu (16 sayfalar), Manuel (12 sayfalar), Manuel (24 sayfalar), Manuel (23 sayfalar), Manuel (27 sayfalar), Manuel (25 sayfalar), En İyi Uygulamalar Kılavuzu (41 sayfalar)

Sayfayı Yazdır

Setting Up Your Dell DR4100 System

Before You Begin

WARNING:

Before you set up and operate your Dell system, review the safety instructions that came with your system.

Dell Software License Agreement

•

Before using your system, read the Dell Software

License Agreement that came with your system.

•

If you do not accept the terms of the agreement,

call the customer assistance telephone number.

For customers in the United States, call

800-WWW-DELL (800-999-3355). For customers

outside the United States, visit support.dell.

com and select your country or region from the

bottom of the page.

Installing the Dell DR4100 Hardware and Conﬁ guring the Network

1. Install the Rails for the Dell DR4100 System

For information about installing the rails for the Dell DR4100 system, see the Rack Installation Instructions that shipped with the rail kit.

2. Set Up the Dell DR4100 System

For information about setting up the Dell DR4100 system, see the Dell DR4100 Getting Started Guide that shipped with the system.

3. Install the Cable Management Arm (CMA) (Optional)

For information about installing the CMA, see the CMA Installation Instructions that shipped with the CMA kit.

4. Log on to the System

The default user name is

administrator

and the default password is

5. Conﬁ gure the Network

The Initial System Conﬁ guration Wizard prompts you to conﬁ gure the system, when you log on for the ﬁ rst time. To conﬁ gure the network:

Type yes and press <Enter>.

Choose either DHCP or static IP addressing

To select DHCP, type Yes at Would you like to use DHCP and press <Enter>. To select static IP addressing, type no and press <Enter>.

If you choose static IP addressing, you will be prompted to enter the static IP address. Enter the static IP address and press <Enter>.

For static IP address, enter a subnet mask, a default gateway address, a DNS suffi x, and a primary DNS address.

You are also asked if you want to conﬁ gure a secondary DNS address.

The Initial System Conﬁ guration Wizard displays a conﬁ rmation screen with all the values you entered in this step.

To change the default host name, type Yes and press <Enter>.

NOTE:

The default host name is DR4100-<Service Tag>

The Initial System Conﬁ guration Wizard displays a screen with the selected interface, IP address choice, host name for the Dell DR4100 system, and the values you set

during step b on conﬁ guring the network.

To accept the settings, type Yes and press <Enter>.

Printed in the U.S.A.

Locating Your System Service Tag

•

Your system is identified by a unique Express

Service Code and Service Tag number. The

Express Service Code and Service Tag are

found on the front of the system. Pull out the

information tag to view the Express Service

Code and Service Tag.

•

Save this information for future reference. This

information is used by Dell to route support

calls to the appropriate personnel.

NOTE:

The illustrations in this document are not

intended to represent a speciﬁ c system.

Check for documentation and information updates on support.dell.com/manuals.

Always read the updates ﬁ rst because they often supersede information in other documents.

Stor@ge!

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly prohibited.

Dell™, the DELL logo, and PowerVault™ are trademarks of Dell Inc..

2012 - 11

•

An active network with available Ethernet cables and connections.

•

If the system has a 1 GbE NIC, connect all four NIC ports (two LOMs and two ports on the NIC card).

•

If the system has a 10 GbE NIC, connect both the 10 GbE ports (two ports on the NIC card).

Verifying Your Solution

NOTE:

•

Network values required are IP addressing, Network Mask, Default Gateway, DNS Suffix, Primary (and

Optional) DNS server, and Host Name. If DHCP is selected, these values are populated based on your

DHCP configuration. If DHCP is not selected, the values must be manually configured.

•

Default values for the DR4100 are:

Dell DR4100 includes:

•

System bezel

•

On the first boot, you must set up the network and the host name for the Dell DR4100 system.

•

Power cords (2)

•

You must connect the Dell DR4100 system to a keyboard and monitor when you setup the system for

•

Power cord retention straps (2)

the ﬁ rst time. After the operating system and network are conﬁ gured, the system can be managed using

•

Mounting rails (2)

a remote browser interface.

•

Cable management arm (optional)

•

To set up the Dell DR4100 system, use an account with administrator privileges.

•

User documentation

Additional Information

Important Updates

NOTE:

After you complete setting up the Dell DR4100 system, check

Apply the updates before using the system for the ﬁ rst time.

•

To update the system software, download the

DR4100 Upgrade File from support.dell.com/support/downloads and apply the upgrade using the web console or CLI.

•

To reinstall the system, download the

Dell DR4100 Restore Manager from support.dell.com/support/downloads.

Documentation

The following documents are available for you at support.dell.com/manuals:

Getting Started Guide also shipped with your system provides an overview of setting up your system, and technical specifications.

•

The

•

The rack documentation included with your rack solution describes how to install your system into a rack, if required.

•

The

Dell DR4100 Administrator's Guide helps you manage your DR4100 solution.

•

The

Dell DR4100 CLI Guide gives you a comprehensive list of all commands to run your DR4100 solution.

•

For hardware issues, see the

Dell DR4100 Owner's Manual .

•

For issues and resolutions for your Dell DR4100 solution, see the

Release Notes .

•

For the full name of an abbreviation or acronym used in this document, see the

Preinstallation Requirements

Do not connect to 1 GbE ports if there is a 10 GbE NIC available on the system.

Use CAT6e copper cables with a 10 GbE NIC.

Default Static System IP: 10.77.88.99

NOTE:

Default static system IP is used only when there is no DHCP server. The default IP can be used

to configure the system using a point to point NIC connection.

Subnet mask IP: 255.0.0.0

Default iDRAC IP: 192.168.0.120

NOTE:

For default iDRAC connection, login name is

root

and password is calvin.

support.dell.com/support/downloads

for any system software updates.

Glossary .