Dialogic Media Board VFX/41JCT-LS Hızlı Kurulum Kılavuzu - Sayfa 2

Ağ Kartı Dialogic Media Board VFX/41JCT-LS için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Dialogic Media Board VFX/41JCT-LS 2 sayfaları. Dialogic media board quick installation guide

Sayfayı Yazdır

3. Insert the board's edge connector into the bus slot.

Use the slot's board guides as you insert the board

edge connector into the slot. Apply pressure only to

the top edge of the board, and press firmly until the

edge connector is securely seated in the slot.

4. Replace and tighten the retaining screw to secure the

board. If the screw is not installed and you attach a

CT Bus cable to the board, the board may be

accidentally unseated from the slot.

5. To install an additional board, select an empty PCI

slot adjacent to the location of the previous board,

and repeat (the second part of) step 2 through step 4.

5. Attach CT Bus Cable to Board (optional)

Colored Stripe (Pin 1)

If you use the board in stand-alone mode, skip the

instructions in this section.

Use a CT Bus cable to connect your board to other

CT Bus form-factor boards in the system.

Caution!

To preserve the electrical integrity of the

CT Bus, use a CT Bus cable with the appropriate

number of connectors ("drops"). We recommend that no

more than two connectors at either end of the cable be

left unused. In addition, it is preferable to distribute the

installed boards in slots along the length of the CT Bus

cable rather than clustered in one area.

Attach the CT Bus cable to the Dialogic board as

follows:

1. Attach the end connector on the CT Bus cable to the

CT Bus edge connector on the top edge of the first

board in the sequence. The connectors are designed

to fit together one way only. If the connector does

not seat fully on the board, turn the cable around and

try again. Make sure that the colored stripe on the

cable faces the rear bracket.

2. Attach the cable to the next board until all boards are

connected by the cable.

Colored Stripe

(Pin 1)

Your CT Bus cable may

have a different number

of connectors (drops).

3. If the cable has extra connectors or is loose, tuck the

cable down so that it does not snag when you replace

the computer cover. See the Caution given earlier in

this section.

6. Connect CT Bus/SCbus Adapter (optional)

If you use the board in stand-alone mode, skip the

instructions in this section.

To connect your board to SCbus form-factor boards, use

the CT Bus/SCbus adapter (part number

882-757-xx). You may use only one CT Bus/SCbus

adapter per system.

1. Before installing the adapter, the Dialogic

boards in

your chassis must be positioned in the correct order.

The board on which the adapter is installed must be

inserted in the first PCI slot adjacent to an ISA slot.

Locate this board.

2. Align pin 1 of the adapter with pin 1 of the edge

connector on the board. Press the adapter onto the

board with the SCbus cable connector facing the rear

edge of the board.

CT Bus / SCbus

Adapter

CT Bus

SCbus

Cable

Colored Stripe

(Pin 1 Indicator)

D/xxx JCT

D/xxx

Board

PCI Slots

ISA Slots

For more information, see the hardware installation

instructions for the CT Bus/SCbus Adapter.

7. Complete Board Installation

After you have installed the board(s) and if applicable

attached cables and adapter, replace the computer cover

and re-attach power cords.

8. Connect External Cables

Each RJ-11 jack on the rear bracket of the voice

board supports a single voice channel. Use each RJ-

11 jack and phone cable to connect each channel to

an analog PBX or standard telephone outlet.

Since this board emulates a standard telephone, a

standard telephone will not function when directly

attached to the board.

Rear

bracket

on board

Channel 1

To analog

Channel 2

PBX

standard

telephone

Channel 3

outlet

Channel 4

J1-J4 on the

Signal

VFX/41JCT-LS Board

Unused

RJ-11 Connector

Station - Earth Recall

Station - Ring

Station - Tip

Unused

Note:

Connect the Earth Recall signal to pin 2. DO

NOT connect Tip or Ring lines to pin 2 or improper

operation of the VFX/41JCT-LS will result.

9. Install Software, Configure and Test

Install the Dialogic

software release and configure the

Dialogic

boards as described in the

Dialogic

Installation and Configuration Guide for your

operating system.

Your application software or Dialogic software release

may have special installation or configuration

requirements. Be sure to read your software

documentation including release note information

before you install the software.

Note:

If you are adding hardware to an existing system,

you do not need to uninstall existing Dialogic

software.

10. Warranty and Return Information

Warranty Period

For specific warranty information for this board, refer to

the Warranty section of the Products page, located at this

URL: http://www.dialogic.com/warranties/.

Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who are

trained to answer technical questions on installing and

configuring Dialogic

products. If you are unsure how

to contact your support channel, please call Dialogic

in the United States at 973-967-6600 (9am-5pm EST)

and we will assist in obtaining the appropriate support

channel. Outside the United States please refer to

http://www.dialogic.com/support/contact

to obtain

local contact information.

Dialogic also provides direct support via Dialogic

Pro™

Services agreements. For more details of direct support

from Dialogic please refer to:

http://www.dialogic.com/support/DialogicPro.

Returning a Product

To return a board for warranty repair or any other returns,

please refer to the following:

http://www.dialogic.com/support/hwfaults. To return a

board for warranty repair, please refer to the following:

http://www.dialogic.com/support/hwfaults. For all other

returns, contact your vendor or Dialogic Customer Support

(for more information, see

http://www.dialogic.com/support/contact/

11. Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales Office

for your area. Address, telephone and fax numbers, are

available at the Dialogic website located at:

http://www.dialogic.com/contact.htm.

To purchase Dialogic

products, please refer to the

following website to locate the appropriate supplier.

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only and

are subject to change without notice and do not represent a commitment on

the part of Dialogic Corporation or its subsidiaries ("Dialogic").

Reasonable effort is made to ensure the accuracy of the information

contained in the document. However, Dialogic does not warrant the

accuracy of this information and cannot accept responsibility for errors,

inaccuracies or omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN

CONNECTION WITH DIALOGIC

PRODUCTS. NO LICENSE,

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY

INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT

BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO

LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY

EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY

INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life

sustaining, critical control or safety systems, or in nuclear facility

applications.

It is possible that the use or implementation of any one of the concepts,

applications, or ideas described in this document, in marketing collateral

produced by or on web pages maintained by Dialogic may infringe one or

more patents or other intellectual property rights owned by third parties.

Dialogic does not provide any intellectual property licenses with the sale of

Dialogic products other than a license to use such product in accordance

with intellectual property owned or validly licensed by Dialogic and no

such licenses are provided except pursuant to a signed agreement with

Dialogic. More detailed information about such intellectual property is

available from Dialogic's legal department at 9800 Cavendish Blvd., 5

Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all

users of its products to procure all necessary intellectual property

licenses required to implement any concepts or applications and does

not condone or encourage any intellectual property infringement and

disclaims any responsibility related thereto. These intellectual property

licenses may differ from country to country and it is the responsibility

of those who develop the concepts or applications to be aware of and

comply with different national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, among

others, are either registered trademarks or trademarks of Dialogic.

Dialogic's trademarks may be used publicly only with permission from

Dialogic. Such permission may only be granted by Dialogic's legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada

H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to

full respect of the trademark guidelines published by Dialogic from time to

time and any use of Dialogic's trademarks requires proper

acknowledgement. The names of actual companies and products mentioned

herein are the trademarks of their respective owners.