Dialogic DM/N1200-4E1-cPCI Hızlı Kurulum Kartı - Sayfa 2

Telefon Aksesuarları Dialogic DM/N1200-4E1-cPCI için çevrimiçi göz atın veya pdf Hızlı Kurulum Kartı indirin. Dialogic DM/N1200-4E1-cPCI 2 sayfaları. Digital telephony interface board for compactpci

Sayfayı Yazdır

board extractors engage the guide holes in the

chassis card cage, then lock down the board

extractors until the red locking tabs snap shut.

CAUTION: CompactPCI backplane pins are bent

easily. Make sure that the board is seated with hand

pressure before fully seating board. If board extractors

are used to seat the board, make sure to seat evenly.

NOTE: If the power to the chassis is on, power is

automatically applied to the board, the Out of Service LED

lights briefly and then goes out, and the Power LED goes

on.

Tighten the retaining screws to secure the board

firmly in the chassis slot (optional).

If the power to the chassis is turned OFF, turn the

power to the chassis ON.

Connecting External Cables

For information about the pinouts for the network interface

cable, refer to the Pinouts for the RJ-48C figure.

Pinouts for the RJ-48C

Pinouts for the RJ–48C

RJ-48C Network Interface

Jack on Bracket

Cable Connector

CHASSIS GROUND

Pin 1

CHASSIS GROUND

UNUSED

XMIT_TIP

XMIT_RING

UNUSED

RCV_TIP

RVC_RING

After Installing the Hardware

After installing the hardware, proceed with the Dialogic

System Software installation as described in the system

software documentation (if applicable).

For technical specifications and product information, see

the Dialogic website at

http://www.dialogic.com/products.htm

Removing the Main Board

Exercise caution when removing the board from a

CompactPCI chassis. The board extractors are equipped

with red locking tabs that lock when the board is correctly

positioned in the chassis.

To remove the board from the chassis, simultaneously

press down both red locking tabs (see the CompactPCI

Extractor figure) on the extractors before applying

pressure away from the center of the board to disengage.

CAUTION: When removing the board, if the red locking

tabs on the extractors are not pressed while applying

pressure to the extractors, there is a risk of breaking the

tabs.

CompactPCI Extractor

Press and hold down the red

locking tabs on both board

extractors before applying

pressure to the board.

Removing the Rear I/O Module

NOTE: In a live insertion (powered-on) system, do not

remove and replace a Rear I/O module while the main

(front) board is in service. Remove the front board first,

then remove and replace the Rear I/O module, and then

reinsert the front board.

To remove the board from the chassis, simultaneously

press down both red locking tabs (see the CompactPCI

Extractor figure) on the extractors before applying

pressure away from the center of the board to disengage.

Warranty and Return Information

Warranty Period

For specific warranty information for this board, refer to the

Warranty section of the Products page, located at this

URL: http://www.dialogic.com/warranties/.

Contacting Technical Support

Dialogic provides technical support for its products through

a network of value added distributors who are trained to

answer technical questions on installing and configuring

Dialogic

products. If you are unsure how to contact your

support channel, please call Dialogic in the United States

at 973-967-6600 (9am-5pm EST) and we will assist in

obtaining the appropriate support channel.

Outside the United States please refer to

http://www.dialogic.com/support/contact

local contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements. For

more details of direct support from Dialogic please refer to:

http://www.dialogic.com/support/DialogicPro.

To return a board for warranty repair or any other returns,

please refer to the following:

http://www.dialogic.com/support/hwfaults.

If you have a sales question, please contact your

local Sales Representative or the Regional Sales Office for

your area. Address, telephone and fax numbers, are

available at the Dialogic website located at:

http://www.dialogic.com/contact.htm.

To purchase Dialogic

following website to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only and are subject to change

without notice and do not represent a commitment on the part of Dialogic Corporation or its

subsidiaries ("Dialogic"). Reasonable effort is made to ensure the accuracy of the information

contained in the document. However, Dialogic does not warrant the accuracy of this information

and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in

this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH

DIALOGIC

PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR

OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU

AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING

TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR

INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life sustaining, critical control

or safety systems, or in nuclear facility applications.

It is possible that the use or implementation of any one of the concepts, applications, or ideas

described in this document, in marketing collateral produced by or on web pages maintained by

Dialogic may infringe one or more patents or other intellectual property rights owned by third

parties. Dialogic does not provide any intellectual property licenses with the sale of Dialogic

products other than a license to use such product in accordance with intellectual property owned

or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed

agreement with Dialogic. More detailed information about such intellectual property is available

from Dialogic's legal department at 9800 Cavendish Blvd., 5

H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual

property licenses required to implement any concepts or applications and does not condone

or encourage any intellectual property infringement and disclaims any responsibility

related thereto. These intellectual property licenses may differ from country to country and

it is the responsibility of those who develop the concepts or applications to be aware of and

comply with different national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol, among others,

are either registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used

publicly only with permission from Dialogic. Such permission may only be granted by Dialogic's

legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any

authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines

published by Dialogic from time to time and any use of Dialogic's trademarks requires proper

acknowledgement. The names of actual companies and products mentioned herein are the

trademarks of their respective owners.

to obtain

Returning a Product

Sales Assistance

products, please refer to the

Floor, Montreal, Quebec, Canada