Miller ArcReach 16 Kullanıcı El Kitabı - Sayfa 10

Kaynak Sistemi Miller ArcReach 16 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Miller ArcReach 16 48 sayfaları.

Sayfayı Yazdır

� Have the installation regularly checked and maintained.

� Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause

interference.

� Electromagnetic energy can interfere with sensitive

electronic equipment such as microprocessors,

computers, and computer-driven equipment such

as robots.

1-4.

California Proposition 65 Warnings

WARNING – This product can expose you to chemicals in-

cluding lead, which are known to the state of California to

cause cancer and birth defects or other reproductive harm.

1-5.

Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, American Welding

Society standard ANSI Standard Z49.1. Website: http://www.aws.org.

Safe Practice For Occupational And Educational Eye And Face Pro-

tection, ANSI Standard Z87.1, from American National Standards In-

stitute. Website: www.ansi.org.

Safe Practices for the Preparation of Containers and Piping for Weld-

ing and Cutting, American Welding Society Standard AWS F4.1 from

Global Engineering Documents. Website: www.global.ihs.com.

Safe Practices for Welding and Cutting Containers that have Held

Combustibles, American Welding Society Standard AWS A6.0 from

Global Engineering Documents. Website: www.global.ihs.com.

National Electrical Code, NFPA Standard 70 from National Fire Pro-

tection Association. Website:

www.nfpa.org

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-

1 from Compressed Gas Association. Website: www.cganet.com.

1-6.

EMF Information

Electric current flowing through any conductor causes localized elec-

tric and magnetic fields (EMF). The current from arc welding (and al-

lied processes including spot welding, gouging, plasma arc cutting,

and induction heating operations) creates an EMF field around the

welding circuit. EMF fields can interfere with some medical implants,

e. g. pacemakers. Protective measures for persons wearing medical

implants have to be taken. For example, restrict access for passers

−by or conduct individual risk assessment for welders. All welders

should use the following procedures in order to minimize exposure to

EMF fields from the welding circuit:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Do not place your body between welding cables. Arrange cables

to one side and away from the operator.

3. Do not coil or drape cables around your body.

OM-278792 Page 4

� Be sure all equipment in the welding area is electromagnetically

� To reduce possible interference, keep weld cables as short as

� Locate welding operation 100 meters from any sensitive electronic

� Be sure this welding machine is installed and grounded according

� If interference still occurs, the user must take extra measures such

For more information, go to www.P65Warnings.ca.gov.

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2 from Canadian Standards Association. Website:

csagroup.org.

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B from National Fire Protection Association.

Website: www.nfpa.org.

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910.177 Sub-

part N, Part 1910 Subpart Q, and Part 1926, Subpart J. Website:

www.osha.gov.

OSHA Important Note Regarding the ACGIH TLV, Policy Statement

on the Uses of TLVs and BEIs. Website: www.osha.gov.

Applications Manual for the Revised NIOSH Lifting Equation from the

and www.sparky.org.

National Institute for Occupational Safety and Health (NIOSH). Web-

site: www.cdc.gov/NIOSH.

SOM 2020–02

4. Keep head and trunk as far away from the equipment in the weld-

5. Connect work clamp to workpiece as close to the weld as

6. Do not work next to, sit or lean on the welding power source.

7. Do not weld whilst carrying the welding power source or wire

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding,

spot welding, gouging, plasma arc cutting, or induction heating opera-

tions. If cleared by your doctor, then following the above procedures

is recommended.

compatible.

possible, close together, and down low, such as on the floor.

equipment.

to this manual.

as moving the welding machine, using shielded cables, using line

filters, or shielding the work area.

ing circuit as possible.

possible.

feeder.