ABB Dodge Quantis BU383 Manuel

Endüstriyel Ekipmanlar ABB Dodge Quantis BU383 için çevrimiçi göz atın veya pdf Manuel indirin. ABB Dodge Quantis BU383 8 sayfaları. Ultra kleen rhb reducer

Sayfayı Yazdır

Dodge

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see baldor.com for updated instruction manuals.

Note! The manufacturer of these products, Baldor Electric Company, became ABB Motors and Mechanical Inc. on

March 1, 2018. Nameplates, Declaration of Conformity and other collateral material may contain the company name of

Baldor Electric Company and the brand names of Baldor-Dodge and Baldor-Reliance until such time as all materials have

been updated to reflect our new corporate identity.

WARNING: To ensure the drive is not unexpectedly

started, turn off and lock-out or tag power source before

proceeding. Failure to observe these precautions could

result in bodily injury.

WARNING: All products over 25 kg (55 lbs) are noted on the

shipping package. Proper lifting practices are required for

these products.

WARNING: High voltage and rotating parts can cause

serious or fatal injury and property damage. The use

of electrical machinery, like all other utilization of

concentrated power and rotating equipment, can be

hazardous. Installation, operation and maintenance

should be performed only by qualified electrical and

mechanical maintenance personnel familiar with NEMA

safety standards, the National Electrical Code and sound

local practices. The manual is to be studied thoroughly by

personnel responsible for the installation and maintenance

of this equipment before installation is begun. Personnel

must be familiar with the potential hazards involved. If this

warning is not observed, personal injury and/or property

damage may result. Keep this document for future

reference.

WARNING: Depending on operating conditions, sound

levels for Quantis products may exceed 70 dB. Protective

measures such as hearing protection may be needed when

in close proximity to a Quantis Reducer in operation.

WARNING: Because of the possible danger to person(s)

or property from accidents which may result from the

improper use of products, it is important that correct

procedures be followed. Products must be used in

accordance with the engineering information specified

in the catalog. Proper installation, maintenance and

operation procedures must be observed. The instructions

in the instruction manuals must be followed. Inspections

should be made as necessary to assure safe operation

under prevailing conditions. Proper guards and other

suitable safety devices or procedures as may be desirable

or as may be specified in safety codes should be provided,

and are neither provided by ABB nor are the responsibility

of ABB. This unit and its associated equipment must be

installed, adjusted and maintained by qualified personnel

who are familiar with the construction and operation of

all equipment in the system and the potential hazards

involved. When risk to persons or property may be

involved, a holding device must be an integral part of the

driven equipment beyond the speed reducer output shaft.

Quantis

Ultra Kleen RHB Reducer

Gearmotors

C-Face Reducers

Separates

Sizes 38 thru 48

WARNING: Quantis products exceeding 30 lb (13.5 kg)

should be lifted using lift-assist equipment rated for

the weight of the product. Weight values for all Quantis

products are listed in the Gearing Engineering Catalog.

Lifting brackets provided on Quantis should be used when

connecting to lift-assist equipment.

WARNING: The Dodge Quantis UK RHB and its connected

equipment and accessories must be guarded. Rotating

parts such as couplings, pulleys, fans and unused shaft

extensions must be permanently guarded by the user

against accidental contact with personnel and their

clothing. The surface temperature of the Dodge Quantis

UK RHB enclosure may reach temperatures which can

cause discomfort or injury to personnel accidentally

coming into contact with hot surfaces. The user should

provide guards to prevent accidental contact with hot

surfaces. Guards must be sufficiently rigid to maintain

adequate guarding in normal service.

WARNING: Threaded hardware used to mount the The

Dodge Quantis UK RHB Unit must be 18-8 Stainless or

Metric A-2 Stainless. DO NOT USE HARDWARE OF A

LOWER GRADE.

Please read these instructions carefully. They contain vital

information on proper installation, operation, maintenance

and service for the Dodge Quantis Ultra Kleen (UK) RHB gear

reducer.

Each Dodge gear reducer is thoroughly inspected and tested at

the factory prior to shipment. Care is taken in packing of each

gear reducer. However, each gear reducer should be thoroughly

inspected before it is accepted from the transportation

company. If any of the goods called for in the bill of lading

are damaged or missing, do not accept the shipment until

the freight agent makes appropriate notation on your freight

bill. If any loss or damage is discovered later, notify the agent

at once and request an inspection. Though ABB Motors and

Mechanical Inc. will be happy to assist you with claims for

loss or damage in shipment, the transportation company is

responsible for reimbursing you for such claims. Claims for loss

or damage in shipment must not be deducted from the ABB

Motors and Mechanical Inc. invoice, nor should payment of the

ABB Motors and Mechanical Inc. invoice be withheld awaiting

claims adjustment. The carrier, not ABB, guarantees safe

delivery. If considerable damage or shortage has occurred and

the situation is urgent, contact the nearest ABB Sales Office.

General