AquaPower AP18RP Kullanıcı El Kitabı - Sayfa 13

Yüzme Havuzu Filtresi AquaPower AP18RP için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. AquaPower AP18RP 16 sayfaları. Aquapower salt water chlorinator

Sayfayı Yazdır
Installation guide
If the cell is installed horizontally, both the inlet & outlet sockets need to face
downwards. This may only be achieved by plumbing 90 degree elbows on either
end of the cell so that they face downwards. Refer to diagram. If you are having
a vertical installation follow the guide on the next page.
Water may flow ONLY in the direction specified on the cell.
Use 2" to 1-1/2" reducers if installed in 1-1/2" plumbing.
Caution: Use only standard type 'N' plumbing adhesive. Contact Aquapower-plus if
you are unsure of what to use.
The cell must be installed on the pool return line downstream of all other equipment
and or equipment take-off and return points. That is after the pump, filter, solar sys-
tem, heater or other receptacles where in excess of 3/4 oz. of gas could accumulate.
If an air blower is connected directly to venturi spa jets, a vented loop must be
installed. This allows any build up of hydrogen gas to escape from the blower line
before it becomes in contact with the blower motor. (Contact Aquapower-plus for
plumbing advice) Ensure sufficient space is kept free for removal of the cell for
inspection purposes.
Where the cell is installed below water level, ensure valves are installed so the water
can be isolated for flood free removal of the electrode.
Ensure the male key-way situated on the electrode cap is positioned into the female
keyway situated on the clear cell body before screwing on the locking nut.
18
SALT: MAXIMUM SALT LEVEL
The high salt level light will begin flashing as the level approaches the upper end
of the ideal range. Operating the unit at higher salt levels would be of no benefit
and these higher levels may affect other pool equipment.
As above, the salt level light will begin flashing as the level
approaches the upper end of the ideal range.
Operating the unit at higher than recommended Salt levels will reduce
cell life and it's ability to self clean.
When do I need to dilute the water?
If the maximum salt level light is flashing, have a sample of water tested by a pool
professional.
If the salt level Is 20% higher then the Ideal recommendation, dilute the water.
Dilute if salt level is 4000ppm or higher
INITIAL SALT DOSAGE
Simply use the following formulas to calculate the amount of salt required.
Add 21 lbs. of salt for every 1,000 gal (3785 litres) of water
Example: Pool volume is 20,000 gallons.
25 lbs. of salt for every 1,000 gal. of water
Multiply 2.5 x 20 (thousand gallons) = 425 lbs. of salt
RECOMMENDED SALT TYPE & HOW TO ADD
Type of Salt
Use Feed grade type salt whenever possible. Use salt that does not contain yellow
Prussiate of Soda. (Prussiate of soda is an anti-caking agent. This may cause
yellow stains on your pool or spa bottom if left on the bottom without being dis-
solved). Salt should be in granular form similar to table salt.
How to add
Never add salt to the skimmer box, this will not harm your Aquapower-plus salt
chlorinator however coarse salt granules may seize the pump impeller.
Always disconnect any automatic cleaners before adding salt and leave them off
until the salt has fully dissolved. Cleaners too may be affected by the coarse gran-
ules and because the salt solution initially formed is denser than water, it remains at
the bottom of the pool. If an automatic cleaner operates through this dense solution,
the cleaners suction hose will drop to the floor and may be damaged as a result.
Cut open bags (normally 50 lbs.) and pour into pool away from skimmer and suction
points. Brush with a pool brush to dissolve quickly.
Do not use salt that contains yellow prussiate of soda. This may cause yellowing on
pool surface.
11