Panasonic WV-SC384 Kurulum Kılavuzu - Sayfa 12
Video Kamera Panasonic WV-SC384 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Panasonic WV-SC384 40 sayfaları. Ip video cameras
Ayrıca Panasonic WV-SC384 için: Kurulum Kılavuzu (40 sayfalar), Teknik Özellikler (2 sayfalar), Kurulum Kılavuzu (40 sayfalar), Entegrasyon Notu (8 sayfalar)
Sayfayı Yazdır
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of
improper installation or operation inconsistent with this documentation.
Installing place
Contact your dealer for assistance if you are unsure of an
appropriate place in your particular environment.
• Make sure that the installation area is strong enough
to hold this product, such as a concrete ceiling.
• When the installation area is not strong enough, rein-
force and strengthen it or use an optional mount
bracket (WV-Q155S, WV-Q155C or WV-Q105A).
• When the product is installed on a wall, use the wall
mount bracket WV-Q154C or WV-Q154S (option).
• When using an outdoor housing to install the product
on the ceiling, use the inner cover (provided with
WV-Q157 or other optional mount brackets). That can
avoid the shape of the camera from reflecting on
images.
• The optional mount brackets for WV-NS202A
(WV-Q150C, WV-Q150S, WV-Q151C, WV-Q151S,
WV-Q152C, WV-Q152S) cannot be used with this
product.
Do not place this product in the following places:
• Locations where it may get wet from rain or water
splash
• Locations where a chemical agent is used such as a
swimming pool
• Locations subject to humidity, dust, steam and oil
smoke
• Locations in a specific environment where a solvent or
a flammable atmosphere exists
• Locations where a radiation, an X-ray, a strong radio
wave or a strong magnetic field is generated
• Locations where corrosive gas is produced, locations
where it may be damaged by briny air such as sea-
shores
• Locations where the temperature is not within −10 °C
to +50 °C {14 °F to 122 °F}.
• Locations subject to vibrations (This product is not
designed for on-vehicle use.)
• Locations subject to condensation as the result of
severe changes in temperature (In case of installing
the camera in such locations, the dome cover may
become foggy or condensation may be caused on
the cover.)
Procure fixing screws separately.
The screws that secure this product are not supplied.
Prepare them according to the material and strength of
the area where the product is to be installed.
12
Screw tightening
• The screws and bolts must be tightened with an
appropriate tightening torque according to the materi-
al and strength of the installation area.
• Do not use an impact driver. Use of an impact driver
may damage the screws or cause tightening exces-
sively.
• When a screw is tightened, make the screw at a right
angle to the surface. After tightening the screws or
bolts, perform visual check to ensure tightening is
enough and there is no backlash.
Be sure to remove this product if it is not in use.
Shielded (STP) LAN cables must be used with this
unit to ensure compliance with EMC standards. *
* For Europe
Radio disturbance
When this product is used near TV/radio antenna, strong
electric field or magnetic field (near a motor, a transformer
or a power line), images may be distorted and noise
sound may be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with IEEE802.3af
standard.
Router
When connecting this product to the Internet, use a
broadband router with the port forwarding function (NAT,
IP masquerade).
Refer to the Operating Instructions (included in the
CD-ROM) for further information about the port forwarding
function.
Time & date setting
It is necessary to set the time & date before putting this
product into operation. Refer to the Operating Instructions
on the provided CD-ROM for descriptions of how to per-
form the settings.