AquaStar 125B NGS Kurulum ve Kullanım Talimatları Kılavuzu - Sayfa 6

Su Isıtıcı AquaStar 125B NGS için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları Kılavuzu indirin. AquaStar 125B NGS 16 sayfaları. Automatic instantaneous type water heaters for use with natural and liquefied petroleum gas

Sayfayı Yazdır

MOUNTING INSTALLATION

The Aquastar 125 B "S" is design certified for mounting

on a wall.

Do not install this appliance on a carpeted wall or over

floor covering which is combustible, such as carpet. The

heater must be mounted on a wall using appropriate

anchoring materials. If wall is a stud wall sheathed with

plasterboard, it is recommended that support board(s),

either 1x4's or 1/2" (minimum) plywood first be

attached across a pair of studs and then the heater

should be attached to the support boards. See Fig 1.

Expansion and contraction of piping due to changing water

temperature in the pipes imparts movement to the heater

which, if mounted directly to a brittle, friable board, such

as plasterboard, can cause failure of mounting.

Before installing the unit, be certain you have the correct

heater for your type of Gas – Propane or Natural Gas.

Identification labels are found on the shipping box, and on

the rating plate which is located on the right side panel of

the cover. Also, each burner orifice is stamped with a

number (79 for LPG and 120 for Natural Gas).

13 ¼"

Fig. 1 - Mounting the Heater

The incandescent particle tray (shipped loose in the car-

ton with the water heater) must be attached at the bottom

of the water heater front cover at the time of installation.

Use the screws provided. See figure 2

Fig. 2 - Incandescent Particle Tray Illustration

VENTING

Vent pipe connection. WARNING: Do not reduce the

vent pipe size.

This appliance must be vented to the outside following all

local ordinances and specifications for installing a gas

appliance vent or chimney. The venting system must be

designed and constructed so as to develop a positive flow

WALL STUDS

SUPPORT BOARD

1" X 4"

SPACE BOARD

SCREWS

INCANDESCENT PARTICLE TRAY

adequate to remove flue gasses to the outdoors. Minimum

vent size must be 5". Minimum height must be 6 feet,

provided there are no elbows. Termination of vent

must be 2 feet above any obstruction within a 10 foot

radius. Consult your gas utility or National Fuel Gas

Code if vent will have elbows or share venting with

another appliance. The vent connector should have

as much vertical rise as possible (minimum 12") before

any horizontal run.

Optional powervent available in order to sidewall vent.

Contact your local dealer. The appliance must be located

as close as practicable to a chimney or vent. The vent

pipe sections must be secured to each other with sheet

metal screws. Keep in mind the minimum clearance from

the top of your heater. Remember also that single wall

vent pipe connectors require a 6 inch clearance from

combustibles. National Fuel Gas Code specifies double

wall — Type "B" — vent pipe be used in cold climates and

for gas vents running through attics. We consider double

wall vent pipe preferable in all circumstances. Any vent

section greater than 45 degrees from vertical is considered

horizontal. Horizontal sections of vent connectors must

slope upwards at least 1/4 inch for every foot of its

horizontal length. Keep the horizontal section short and

avoid too many elbows.

WARNING

Note: The burners of an instantaneous "on demand" water

heater such as the AquaStar are only on at the time that

hot water is actually being used, the venting stack is

therefore cold except for the short durations when hot water

is being used, it is therefore very important that the venting

and air supply be adequate to provide a good positive draft

as soon as the burners turn on. See venting guide on back

page.

The AquaStar 125B"S" instantaneous water heaters have

built-in draft diverters and are designed for indoor

installation only. The draft diverter outlet must be connected

to a clear, unobstructed vent of the same size, or larger.

In Canada, CAN/CGA-B149 Installation Code for

detailed requirements

In U.S.A., ANSI Z223.1 - NFPA 54, national Fuel Gas

Code for detailed requirements.

The flue connection for the AquaStar 125B"S" is 5 inches.

However, in Canada, for installations at high altitude (2000-

4500 feet above sea level) a six inch flue is required. A 5"

by 6" flue adaptor must be affixed to the flue collar of the

AquaStar with at least two screws. See figure 3

Fig. 3 - Flue Adaptor for High Altitude Installations

5" X 6" ADAPTOR

USED ON HIGH ALTITUDE