Aquatec ELAN AQT00063 Kullanım Talimatları Kılavuzu - Sayfa 8

Tekerlekli Sandalye Aquatec ELAN AQT00063 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Aquatec ELAN AQT00063 17 sayfaları.

Sayfayı Yazdır
5.
Fold the sideflaps on the seat inwards (3, fig. 9).
Important!
●
When folding the backrest down, ensure
that the curled cable of the hand control
does not get caught.
●
Do not fold the backrest down if there is wa-
ter in the bath.
6.
Take hold of the backrest at the head-end and fold
it all the way forward (4, fig. 9).
The locking mechanism between the base plate and
seat plate closes automatically.
Important!
●
Release both rear suction cups simultane-
ously.
●
When lifting, please remember that the
bathlift weighs about 11.7 kg (without bat-
tery).
7.
To release the rear suction cups, pull the straps
(16, fig. 1).
8.
Lift the rear end of the seat further (5, fig. 9).
This releases the front suction cups.
Important!
If you have installed the height adapters (op-
tional), you also have to pull the straps on the
front suction cups to release them.
9.
Take the lift out of the bath.
10. Carefully put away all components of the bathlift.
6

Operation

6.1

Control

Important!
●
Only use the battery supplied.
●
If the battery does not have enough charge,
the red battery pilot light goes on (2,
fig. 10). In this case, the lowering function is
disabled. However, you can still raise the
lift. Recharge the battery immediately after
you have raised it.
●
The hand control device may only be used
when the backrest is properly mounted and
in upright position.
●
If you let go of the button, the lift stops in-
stantly in its position.
You use the hand control (fig. 10) for controlling the
bathlift.
7
6.1.1

Lifting

Press the UP button (3, fig. 10) on the hand control (4,
fig. 10). The seat moves upwards.
6.1.2

Lowering

Press the DOWN button (5, fig. 10) on the hand control
(4, fig. 10). The seat moves downwards.
6.1.3

Emergency stop

Important!
Only press the red emergency stop button in
the case of an emergency.
In an emergency situation, such as if the UP or DOWN
button is jammed, press the emergency stop button (1,
fig. 10).
The bathlift stops moving immediately.
On letting go of the emergency stop button and after
having repaired the fault if this is the case, the bathlift
is ready for use again.
6.2

Using the bathlift

CAUTION!
The seat may slip if the suction cups do not
adhere properly.
Before you use the bathlift, make sure that it
is securely positioned and cannot tip over,
and that the spindle foot is sitting properly in
the spindle foot retainer.
Important!
●
Before you take a bath, do a test run* to
make sure that the bathlift functions proper-
ly.
●
Before using the bathlift, check the temper-
ature of the bath water.
Section 5.3 describes how to set up the bathlift in the
bathtub.
1.
Raise the seat until it is level with the edge of the
bath by pressing the UP button (3, fig. 10).
The sideflaps should be level and rest on the edge of
the bathtub.
2.
Fill the bath with water and check the tempera-
ture.
3.
Sit down on the sideflap nearest to you as you
would sit down on a chair.
4.
Slide backwards until you are sitting in the middle
of the seat.
* Run the bathlift unloaded once to the top and then
back to the bottom.
EN