Aquatec AQUAPRO AP3000 Kullanım Kılavuzu - Sayfa 2
Su Pompası Aquatec AQUAPRO AP3000 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Aquatec AQUAPRO AP3000 2 sayfaları. Waterfeature pump
Sayfayı Yazdır
Congratulations on your purchase of this product by AquaPro,
the answers for your watergarden made easy!
VOLTAGe (V)
POWer (WATTS)
MAX HeIGHT (M)
FLOW MAX (L/H)
OuTLeT
DESCRIPTION AND FEATURES
Your Aquapro waterfeature pump has been
manufactured with advanced technology to
provide you with the best quality pump for
your pond or waterfeature.
• Aquapro pumps are suitable for use in
many different applications including;
fountains, water features, small ponds
and hydroponics.
• Your Aquapro pump has a single moving
part (an impellor set) therefore enabling
easy cleaning
and maintenance.
• The motor and electrical components
are encapsulated in epoxy resin,
ensuring safe operation under water.
AP1050
AP2000
AP3000
240
240
240
18
35
75
1.8
2
3
1050
2000
3000
19mm
19mm
19mm
INSTALLATION
1. If required, have a qualified electrician
install weather proof power point near
to the pond or waterfeature, (within the
cable length of the pump).
2. Place the pump in desired location,
ensure the pump is on a stable surface
that is free of sludge, sand and other
debris and connect tubing to the outlet
or attach fountain kit.
3. ensure pump is submerged then plug in
power cord and switch on.
MAINTENANCE
Disconnect power cord from the power
supply before performing maintenance.
Never lift the pump by the power cord. The
only serviceable item is the impellor set.
The motor unit of the pump is
encapsulated with epoxy resin and does
not need lubrication.
All Aquapro submersible pumps are water
cooled; if pump becomes restricted it
will overheat and could cause permanent
damage. ensure pump does not become
blocked or restricted.
The power cord cannot be replaced,
if the cord is damaged, the pump must
be discarded.
The impellor set is a wearing consumable
part. Regular inspections, cleaning and
maintenance of impellor is necessary to
ensure longer impellor life.
If the impellor set becomes worn or
damaged it should be replaced (available
from your dealer or special orders). Failure to
do so may cause serious damage to pump.
1. Disconnect the power cord from
the power supply before performing
maintenance.
2. Remove the pump from water, detach
tubing/ fountain kit and remove front
cage from pump.
1 Front Cover
2 Biosponge
3 Flow Controler
4 Impellor Locking ring
5 Impellor Cover
6 Impellor
7 Motor Body
1
2
AP1050 Model shown. Picture for illustration purposes only.
WATERFEATURE PUMP
instructions manual
3. remove the impellor locking ring/ cover
by either turning anti-clockwise and
pulling out.
4. Gently remove the impellor and shaft,
use long nose pliers if needed. Take
care not to break ceramic shaft (if
applicable) because they are brittle.
5. Clean impellor, checking for any signs of
wear or damage.
6. reinstall the shaft, and then carefully
slide the impellor onto the shaft. The
impellor will pull itself in by magnetic
force, this is normal. (Take care not to
pinch your fingers).
7 . replace the impellor cover making sure
the shaft is located properly on the
impellor cover.
8. replace the front cage.
9. re-attach tubing/fountain kit, submerse
in water, connect to power supply and
turn on.
3
4
5
6
7