Aquatec PONDMAX PU10500 Kullanım Kılavuzu - Sayfa 3

Su Pompası Aquatec PONDMAX PU10500 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Aquatec PONDMAX PU10500 8 sayfaları. Filtration & waterfall pumps

Sayfayı Yazdır

FILTRATION & WATERFALL PUMPS

BENEFITS

PondMAX Filtration & Waterfall Pumps are suitable for use in many different applications including waterfalls

and Biological Filter systems. Your pump has a single moving part (an impeller set) enabling easy cleaning and

maintenance.

• PondMAX Filtration & Waterfall Pumps are suitable for use in many different applications including waterfalls

and Biological Filter systems. Your pump has a single moving part (an impeller set) enabling easy cleaning and

maintenance.

• The Pumps have intelligent circuitry that analyses the speed and torque of the motor. It will increase and decrease

the energy usage to maximise efficiency. The soft start nature of the system helps to avoid sudden pressure surges

causing pipes to blow off. The intelligent system will change the motor speed to maximise the flow of water in

• the given circumstances. If the Impellor gets jammed or stops, the circuitry will sense the state and cut the power

automatically. This procedure will repeat 3 times. If the rotor is still jammed, it will activate a prolonged low state, till

the pump is turned off, and adequate maintenance is carried out. Thus minimising motor burnout, due to electrical

heat, through lack of water flow through the motor.

• The motor and electrical components are totally encapsulated in epoxy resin, ensuring safe operation under water.

• The pump has a robust bearing and shaft design so no oil/grease lubrication is required.

• PondMAX Filtration & Waterfall Pumps are continuous rated therefore are designed to be heavy-duty and to

operate 24/7.

IMPORTANT SAFEGUARDS

Please read the operating instructions and familiarize yourself with the equipment before placing it

in service. Correct and safe use of the system requires strict compliance with the safety instructions.

For safety reasons persons less than 16 years of age or people that are not familiar with these

instructions should not use this equipment.

• Any damage to the equipment or unmerited operation

will bring dangers to the surrounding precincts. So if

there is any damage of the equipment, it must not to

be used. The equipment should be placed out of reach

of children.

• For your own safety, disconnect from the power supply

before any maintenance of any equipment is attempted

on the tank or water body. Always unplug the pump

from the power supply when not in use

• Never pull the cable to disconnect the plug from the

power supply - Grasp the plug and pull to disconnect.

If required, have a qualified electrician install a

weatherproof power supply point near to the pond

or water-feature (within the cable length of the

appliance).

• Be sure the equipment is submerged completely in the

water. The depth should not be greater than 2m.

• Do not operate the pump if the appliance or any

components of the system, such as the power cable,

have been damaged. Check appliance for defects

regularly.

• Always use a properly grounded power supply that is

connected to an RCD with a rated residual operating

current not exceeding 30mA. As per AS/NZS

3350.2.41:1997

PMAX PU Pumps Instructions.indd 3

• To avoid an electric shock, do not attach the plug to the

• Do not cut the cable as this will result in voiding your

• Do not install or store the appliance where it will be

• Care should be taken to arrange the power cable so

• Do not attempt to repair the electrical appliance

W A T E R G A R D E N I N G T O T H E M A X

SUBMERSIBLE

power supply socket with wet hands. On installation,

the drip loop method should be used to prevent water

from traveling down the cable and onto the plug or

power supply. If the plug does get wet, do not unplug

the cable. Immediately disconnect the circuit breaker

that supplies power to the power supply point. Then

unplug and examine the plug, and power supply point,

for presence of water. If the power point has become

wet, you should consult an electrician before using the

power point again.

warranty.

exposed to extreme hot or cold temperatures. Do not

use in water above 35°C.

that it cannot be accidentally tripped over or pulled.

yourself. Return to an authorized service centre

or place of purchase if a fault occurs, (regular

maintenance is not considered repair and is required

by user).

26/7/17 1:03 pm