HP Xw460c - ProLiant - Blade Workstation Kurulum Talimatları

Anahtar HP Xw460c - ProLiant - Blade Workstation için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. HP Xw460c - ProLiant - Blade Workstation 2 sayfaları. Mezzanine card installation instructions for supported hp proliant c-class bladesystem servers
Ayrıca HP Xw460c - ProLiant - Blade Workstation için: Uygulama Kılavuzu (35 sayfalar), Hata Önleme Kılavuzu (12 sayfalar), Teknik Beyaz Kitap (12 sayfalar), Ürün Yazılımı Güncellemesi (9 sayfalar), Kurulum Kılavuzu (2 sayfalar), Sıkça Sorulan Sorular Kılavuzu (14 sayfalar), Kurulum Posteri (9 sayfalar), Kurulum Kılavuzu (33 sayfalar), Yönetim Kılavuzu (28 sayfalar), Donanım Kılavuzu (23 sayfalar), Genel Bakış (35 sayfalar), Kullanıcı Kılavuzu (33 sayfalar), Optimizasyon Kılavuzu (13 sayfalar), Sınırlı Garanti (10 sayfalar), Kurulum Talimatları Kılavuzu (10 sayfalar), Kurulum Talimatları Kılavuzu (8 sayfalar), Kurulum Talimatları (4 sayfalar)

Sayfayı Yazdır
HP Xw460c - ProLiant - Blade Workstation Kurulum Talimatları

Mezzanine Card

Installation Instructions

for supported HP BladeSystem c-Class server blades
© Copyright 2006 - 2007 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
April 2007 (Second Edition)
Part Number 413773-022
Overview
Use these instructions to install optional mezzanine cards.
Optional mezzanine cards are classified as Type I mezzanine
cards and Type II mezzanine cards. The type of the
mezzanine card determines where it can be installed in the
server blade.
Install Type I mezzanine cards on Mezzanine 1 connector,
Mezzanine 2 connector, or Mezzanine 3 connector.
Install Type II mezzanine cards on either Mezzanine 2
connector or Mezzanine 3 connector.

Warnings and cautions

WARNING: To reduce the risk of personal injury
from hot surfaces, allow the drives and the internal
system components to cool before touching them.
WARNING: Reduce the risk of electric shock by
removing all AC power from the system before
installing or replacing any non-hot-plug hardware
option. Disconnect all power cords to completely
remove power from the server.
CAUTION: Electrostatic discharge (ESD) can
damage electronic components. Be sure that you are
properly grounded (earthed) before beginning any
installation procedure.
CAUTION: Limit the number of times that a
mezzanine card is installed and removed within its
lifecycle to prevent connector pin damage.

Removing the access panel

Identify the proper server blade in the enclosure.
1.
Back up all server blade data.
2.
Power down the server blade.
3.
Remove the server blade.
4.
Lift the access panel latch and slide the access panel to
5.
the rear.
Remove the access panel.
6.

Installing the mezzanine card

IMPORTANT: Remove the mezzanine card
connector protective cover, if installed.