aquatherm AT115 Kullanıcı El Kitabı - Sayfa 10

Isıtıcı aquatherm AT115 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. aquatherm AT115 10 sayfaları.

Sayfayı Yazdır

d. Without knowledge of the correct lock code, and with the ULC enabled,

control adjustments will not be possible. Be certain to record your loCK

code in a safe place. The lock code may be changed any number of times

by following the instructions detailed in this section.

B. DE-ACTIVATING THE USER LOCK CODE [ULC] FUNCTION:

1) Following the instructions detailed previously at: "8, 6)", press any key and

enter the user lock code number; then press the [POOL/SPA] key.

2) Immediately following the entry of the user lock code, simultaneously press

and hold the [UP ARROW] and [DOWN ARROW] keys until the code [CF1]

appears on the display.

3) Then, use the [POOL/SPA] key to scroll to the [ULC] message; press the

[DOWN ARROW] key to change the display to "0". This will disable the

User lock function.

C. USER LOCK CODE IS ACTIVATED, BUT PASS NUMBER IS NOT

KNOWN ("BACK DOOR ENTRY"):

Note: Should the ULC option be enabled, and a lock code number other than

the factory default (0) be installed but is unknown, the following procedure

may be followed to regain controller programming access:

1) Simultaneously press and hold the [POOL/SPA] and [UP ARROW] keys until

the display shows "888". This operation will reset the controller to the factory

default settings.

2) When reset to the factory default settings the user lock code [ULC] is deacti-

vated and the user lock code number [ELC] is reset to "0."

3) In addition, all other settings are returned to the factory defaults. If an exter-

nal controller is in use, contact Aquatherm Heat Pumps (888-297-3826); ask

for assistance with re-configuring the controller for use with an external con-

troller.

AT START UP: CONTINUOUS CIRCULATION

PUMP OPERATION REQUIRED

When starting a heat pump for the first time, it must be permitted to operate, continu-

ously, until the desired water temperature is attained. This may take several hours,

to several days, depending upon the size of the pool or spa and weather conditions.

If a time clock or similar device controls the operating times of the water circula-

tion pump, temporarily override the water pump controller, allowing for 24-hour,

continuous water pump operation.

Once the body of water has reached the desired temperature, the water pump

controller can be reset.

Seasonal Use & Shut Down

During Swim Season

•

During the swim season, even if the pool or spa is not in use, allow water to

flow through the heater. Doing so eliminates the need to reposition valves

when you do wish to heat the pool or spa.

•

During periods when heating or cooling is not desired, leave heater controls

in the OFF position.

Freeze Protection & Extended Shut Down

In areas where freezing conditions are a rare occurrence, allow the filtration system

to run continuously throughout the freeze period. Typically, during light freeze

conditions, circulating (moving) water will not freeze.

In areas where freezing conditions are prevalent and sustained, the heat pump

MUST be winterized; please refer to winterizing instructions, below, and on the

following pages. Failure to properly winterize your heat pump could result in

permanent damage to the unit.

1. Disconnect all electrical power to the heater; turn OFF circulating pump.

2. At the two (2) connection unions, disconnect the plumbing to the heater

(removal is counter- clockwise).

3. If your unit has an external drain plug, remove plug. This plug would be

located at lower, front corner of heater. (position may vary between models).

Allow water to drain out of the condensor. DO NOT replace plug until final

winterizing step.

4. If no external drain plug is found, it will be necessary to open access panel

and see if heat exchanger has an internal drain plug. If so, remove plug, and

allow water to drain out of the condensor.