Diamond Tech Studio Pro Precision 2000 Kullanım Kılavuzu - Sayfa 7
Testere Diamond Tech Studio Pro Precision 2000 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Diamond Tech Studio Pro Precision 2000 8 sayfaları.
C. Rheostat Installation
Use of Rheostat allows blade speed to slow down for intricate or delicate cuts. Slowing the speed will also prevent
glass from heating too rapidly, which may cause glass to glow red or crack.
1) Remove the power cord from the saw. Plug rheostat into power cord outlet located on the right side of the saw
underneath the ON/OFF switch (Fig.20).
2) Plug the saw power cord into the rheostat (Fig.21).
3) Plug both the pump and rheostat into a dedicated power strip with an on/off toggle switch. Using a power strip
will allow you to turn the pump and saw on and off safely at the same time.
Fig.20
QUICK TIPS
1) Do not force materials into the blade. Ease the materials into the blade, turning as you go to create your pattern.
Avoid twisting the blade on tight curves.
2) To back out of a cut, turn the saw off and ease the material away from the blade.
3) Clean band saw after each use with lukewarm water.
4) When storing for extended periods of time, remove blade and drain water supply system.
5) Use a waterproof pen to mark your pattern on the material. For added protection allow the ink to dry and use a
Chap Stick™ or rubber cement over line before cutting.
6) When cutting material the highest blade speed will usually result in the fast and smoothest cutting. Use a slower
speed when working with delicate materials or making very tight turning radius.
7) When cleaning the wood blade, it is best to avoid using abrasive cleaners, as they can scratch the surface of the
blade which may affect performance. Additionally, scratches in the surface of the blade will fi ll with pitch, making it
more diffi cult to clean the next time. To clean blades, soak with oven cleaner.
8) Should the blade jam in material being cut, immediately turn OFF power switch and wait until all moving parts have
stopped. Gently free work materials, holding blade against the blade guides to prevent it from stretching or badly
twisting. Back out of the cut if needed. Inspect blade for kinks and ensure there is no remaining debris in the blade
path which may have caused the jam.
ADDITIONAL PARTS
I
e t
m
PRECISION 2000™ DIAMOND BLADE
PRECISION 2000™ "THE CHOPPER"WOOD BLADE #WB0450
PRECISION 2000™ BLADE GUIDES
P
R
E
C
S I
O I
N
0 2
0 0
™
M
O
T
O
R
P
R
E
C
S I
O I
N
0 2
0 0
™
F
U
E S
Diamond Tech offers a Diamond Blade repair service should a blade break with ample diamond remaining. Return blade to
Diamond Tech, Blade Repair Service, 5600 Airport Blvd., Suite C, Tampa, FL 33634. When returning a blade for repairs,
make sure you include your name, addresses, daytime phone number @ area code, saw model and type of payment.
Blade repair service does not cover wood or metal cutting blades. For International and special handling, please include
extra postage and shipping instructions Blade Repair Fees (U.S. Dollars):
Precision 2000, DL1000, DL3000, DL3000XL, Speedster, SpeedsterXL...........................................................$25.00
DL5000................................................................................................................................. $45.00
Fig.21
I
e t
m
N
u
m
b
r e
I
e t
m
#22
PRECISION 2000™ FUSE HOLDER
PRECISION 2000™ ANGLE GUIDE
#513
PRECISION 2000™ UPPER WHEEL
#
P
6
0 5
P
R
E
C
S I
O I
N
#
P
6
3 5
P
R
E
C
S I
O I
N
0 2
0 0
™
L
O
W
E
R
W
H
E
L E
0 2
0 0
™
W
A
T
E
R
B
O
T
T
E L
I
e t
m
N
u
m
b
r e
#P654
#P656
#P674
#
P
6
5 7
#
P
9
1 1