S
F
P
E
C
I
L
3-Chip DLP™ Projector
Optional board slot *
5
:
With ET-MD77SD1 installed:
With ET-MD77SD3 installed:
With ET-MD77SD4 installed:
With ET-MD77DV installed:
Power cord:
Cabinet material:
Dimensions (W x H x D):
Weight:
Operating temperature*
6
:
Operating humidity:
Remote Control Unit
Number of functions:
Power supply:
Operation range*
:
7
Dimensions (W x H x D):
Weight:
Optional Accessories
Zoom lens (0.9 – 1.1:1):
Zoom lens (1.4 – 1.8:1):
Zoom lens (1.8 – 2.8:1):
Zoom lens (2.8 – 4.6:1):
Zoom lens (4.6 – 7.4:1):
Zoom lens (7.3 – 13.8:1):
Fixed-focus lens (0.7:1):
SD-SDI/network board:
HD-SDI/SD-SDI/network board:
DVI-D/network board:
Replacement lamp unit
Ceiling mount bracket for high ceilings
Ceiling mount bracket for low ceilings
Frame
Carrying handle
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1
Values indicate overall average values of the product at the time of shipment and are stated based on JIS X 6911:2003 Data Projector
Specification Sheet Format. Measurement method and conditions are based on Appendix 2.
*2
Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*3
Shift range is limited during simultaneous horizontal and vertical shifting.
*4
Contact your dealers for details when the control using RS-232C or RS-422 is required.
*5
The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*6
Operating temperature is 0°C – 40°C (32°F–104°F) when the fan control is set to "HIGHLAND" (for over 1,400 m to 2,700 m above sea level).
*7
Operation range differs depending on environments.
As of July 2007
E
SERIAL IN:
BNC x 1, SD-SDI signal (4:2:2), SMPTE 259M compliant, 480i, 576i
SERIAL OUT:
BNC x 1, active through
SERIAL IN:
BNC x 1
SD-SDI signal (4:2:2): SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YC
piant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p
SERIAL OUT:
BNC x 1, active through
Link A/Link B IN:
BNC x 1 for each
Single-link HD-SDI signal (YC
piant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M com-
piant, 1920 x 1080/24p, 1920 x 1080/24sF
Dual-link HD-SDI signal (X´Y´Z´ 4:4:4 12-bit): 2048 x 1080/24p, 2048 x
1080/24sF
DVI-D IN:
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
EDID1: 480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF,
1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
EDID2: Compatible with non-interlaced signals only,
VGA (640 x 480) – U-XGA (1,600 x 1,200), dot clock: 25–162 MHz
NOTE: LAN terminals on the optional board can not be used. Use the LAN terminal
3 m/9.8´
Moulded plastic
578 x 320 x 643 mm (22-3/4˝ x 12-19/32˝ x 25-5/16˝) (without lens)
32 kg (70.5 lbs) or less (without lens)
0°–45°C (32°–113°F)
10%–80% (no condensation)
35 keys, 39 functions
3 V DC (AA battery x 2)
Approx. 30 m when operated from directly signal receptor
51 x 22.7 x 176 mm (2˝ x 7/8˝ x 6-15/16˝)
134 g (4.7 oz) (including batteries)
ET-D75LE6
ET-D75LE1
ET-D75LE2
ET-D75LE3
ET-D75LE4
ET-D75LE8
ET-D75LE5
ET-MD77SD1
ET-MD77SD3
ET-MD77DV
ET-LAD10000 (one unit)
ET-LAD10000F (a set of four lamps)
ET-PKD100H
ET-PKD100S
ET-PFD100
ET-HAD100
C
B
R
C
B
R
on the projector.
PT-DW10000
4:2:2 10-bit): SMPTE 292M com-
4:2:2 10-bit): SMPTE 292M com-
< 3 >
Sayfayı Yazdır