Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls Kullanım Talimatları Kılavuzu - Sayfa 28
Projektör Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls 33 sayfaları. Micro portable wireless xga lcd projector
Ayrıca Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls için: Teknik Özellikler (4 sayfalar)
Sayfayı Yazdır
On-screen display
Displayed for 30
seconds. Pressing any
More than 1 800 hours
button will clear the
display.
Remains displayed until
More than 2 000 hours
any button is pressed.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 2 000 hours (when "LAMP POWER" has
been set to "HIGH" and when "AI" has been set to "OFF"), the projector will
switch to standby mode after approximately 10 minutes of operation. The
steps ) to - on the next page should thus be completed within 10 minutes.
# Disconnect the power cord
from the projector by following
the procedure on page 26, and
check that the area around the
lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover.
Lamp unit cover
Lamp unit cover fixing screws
54-E
NGLISH
LAMP indicator
Illuminates red during
image projection and
standby mode.
% Use a Phillips screwdriver to
loosen the two lamp unit fixing
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
Handle
A
B
Lamp unit fixing screws
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B.
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection
circuit to operate so that the
power cannot be turned on.
( Connect the power cord.
) Press the POWER button so
that a picture is projected onto
the screen.
NOTE:
B If the power cord was
disconnected during projection
when the projector was used
the last time, projection will start
after the power cord is
connected (when "POWER
MEMORY" in the "OPTION2"
menu is set to "ON"). Refer to
page 46 for details.
* Press the MENU button to
display the "MAIN MENU", and
then press the F or G button
to select "OPTION2".
M E N U
K E Y S T O N E
P I C T U R E
P O S I T I O N
I N D E X W I N D O W
S H U T T E R
V O L U M E
L A N G U A G E
O P T I O N 1
O P T I O N 2
S E C U R I T Y
N E T W O R K
S E L E C T
E N T E R
E X I T
+ Press the ENTER button to
display the "OPTION2" menu,
and then press the F or G
button to select "LAMP
RUNTIME".
O P T I O N 2
B A C K C O L O R
B L U E
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
S T A N D A R D
L A M P P O W E R
H I G H
L A M P R U N T I M E
1 8 2 0 H
F U N C 1
I N D E X
C O N T R O L K E Y
O N
A U T O P O W . O F F D I S A B L E
P O W E R M E M O R Y
O N
S E L E C T
R E T R N
, Press and hold the ENTER
button for approximately 3
seconds.
O P T I O N 2
B A C K C O L O R
B L U E
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
S T A N D A R D
L A M P P O W E R
H I G H
T I M E R E S E T [ P O W E R O F F ]
F U N C 1
I N D E X
C O N T R O L K E Y
O N
A U T O P O W . O F F D I S A B L E
P O W E R M E M O R Y
O N
S E L E C T
R E T R N
The "LAMP RUNTIME" will
change to "TIME RESET
[POWER OFF]".
NOTE:
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative usage
time for the lamp unit to "0".
Refer to page 26 for details on
how to turn off the power.
E
-55
NGLISH