Dicon 650MRB Kullanıcı El Kitabı

Duman Alarmı Dicon 650MRB için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Dicon 650MRB 2 sayfaları. Mains powered smoke alarms & heat alarms
Ayrıca Dicon 650MRB için: Kullanıcı El Kitabı (2 sayfalar)

Sayfayı Yazdır

M A I N S

SMOKE ALARMS

& HEAT ALARMS

OWNERS

MANUAL

COVERS • Simple Fitting Instructions • Location Guide

For further information

please write:

Dicon Safety Products (Europe) Ltd.

P.O. Box 402

GLOUCESTER

650M, 650MC, 650MRB 650MRL, 650MBX

GL2 9YB

680M, 680MC, 680MRL, 680MRB, 680MBX

2502-A0033

CHECKS BEFORE USE

370MBX, 650MBX, 670MBX, and 680MBX:

• Check battery has been fitted correctly.

• Check alarm is not beeping.

• Test alarm before switching on the electricity supply.

• Check the green light is on (behind the front grille).

• Check the red light flashes every 45 seconds or so.

• When testing linked alarms check that they all

interconnect within 10 seconds.

IMPORTANT NOTES

• On the 370MBX the alarm will beep for 10 minutes

if the pause button has been pressed.

• Alarms with rechargeable batteries or capacitor

back up may beep for up to 2 hours while the

batteries / capacitors charge.

• Leave a copy of this handbook with the user and ensure

they know how to use and maintain the alarm.

P O W E R E D

• User Information • Basic Fire Safety Tips

• Simple Maintenance Instructions

MODELS:

PHOTOELECTRIC SMOKE ALARMS

IONIZATION SMOKE ALARMS

670M, 670MC, 670MRB, 670MRL,

670MBX, 370MBX

HEAT ALARMS

220-240VAC (

)

MAINS POWERED ALARMS

CLASS II APPARATUS

IMPORTANT: PLEASE READ

AND RETAIN THIS OWNERS MANUAL

When installing this alarm for use by others, please

leave this manual or a copy with the end user.

All Alarms:

A: GUIDANCE ON INSTALLATION

WARNING: Wiring should be installed by a qualified electrician in accordance with BS7671.

Permanent connection to the fixed wiring of the building should be made in a suitable junction box.

This alarm must not be exposed to dripping or splashing. Connect the alarm as late as possible in

an installation, particularly in new build, to avoid contamination. Remove the dust cover before

applying power.

NOTE: For detailed guidance on the siting of this alarm refer to section C of this handbook.

IMPORTANT: The circuit used to power the alarm must be a 24 hour voltage circuit that cannot be

turned off by a switch. BS5839 Part 6 states that: -

For mains powered alarms, each with an integral standby supply (Grade D), the mains electricity

supply should take the form of either:

a) an independent circuit at the dwelling's main circuit board, in which case no other electrical

equipment should be connected to this circuit (other than a dedicated monitoring device

installed to indicate failure of the mains electricity supply to the alarms); or

b) a separately electrically protected, regularly used local lighting circuit.

For mains powered alarms, with no standby supply (Grade E), the mains electricity supply may

only take the form of an independent circuit as per a) above. If it is necessary to use an RCD for

protection, it should operate independently of any RCD protection for circuits supplying sockets or

portable equipment.

All interconnected alarms should be installed on a single final circuit.

NOTE: The maximum interconnect wiring length is 250 metres. The maximum number of alarms

interconnected together is 12. Dicon smoke alarms should not be connected to any model

produced by another manufacturer.

The location of the alarms must comply with the applicable building codes and the advice in

section C: WHERE TO LOCATE below.

B: INSTALLATION (See Diagrams 1 & 2)

1. IMPORTANT INFORMATION: THE COLOUR CODING FOR ELECTRICAL CABLES USED IN

BUILDING WIRING HAS BEEN CHANGED AS FOLLOWS:-

Old colour

New (harmonised) colour

Red

Brown

Yellow

Black

Blue

Grey

Black

Blue

The new (harmonised) colour cables may be used on site from 31 March 2004. New installations

or alterations to existing installations may use either new or old colours, but not both, from 31st

March 2004 until 31st March 2006. Only the new colours may be used after 31 March 2006. For

more information see Amendment No: 2 to BS 7671:2001 and guidance publications.