Epcom TD-9554S2A Hızlı Başlangıç Kılavuzu - Sayfa 2
Güvenlik Kamerası Epcom TD-9554S2A için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Epcom TD-9554S2A 2 sayfaları.
Sayfayı Yazdır44.2
38.2
④
Route and connect the cables. T hen secure the mounting base to the
ceiling or wall with the screws provided.
⑤
Install the dome and enclosure to the mounting base and then adjust
the dome to obtain an optimum view angle. Finally, fix the camera with
the fixed screw.
5
Network Connection
In LAN, there are two ways to access the camera. 1. Access Through
IP-Tool; 2. Direct Access Through WEB Browser
● Access Through IP-Tool
(mm)
Ø91.6
IPC
① Make sure that the camera and the PC are connected to the local
Ø51.0
network.
② Install IP-Tool from the CD and run it after installation.
Ø4.5
Immediate Refresh
Device Name Device Type
name
IPC
name
IPC
name
IPC
Total Device: 3
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as the
computer's. Please modify the IP address of your device according
to the practical situation.
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please enter the password of the administrator and click
"Modify" button to modify the setting.
The default password of the administrator is "123456".
④ Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM. Follow directions to download and run the
plugin in the computer. Then enter the user name and password in the login
interface.
Switch
Network Cable
Network Cable
Computer
Router
Device Network Search
Product Model
IP Address
Http Port
Data Port
Subnet
Modify Network Parameter
unknown
192.168.226.201
80
9008
255.255.
Mac Address
CE :98 :23 :75 :35 :22
unknown
192.168.1.2
80
9008
255.255.
IP Address
192 .168 . 226 . 201
Subnet Mask
255 . 255 . 255 . 0
unknown
192.168.1.3
80
9008
255.255.
192 .168 . 226 . 1
Gateway
i
Tip: Enter the administrator password, and
then modify the network parameters.
Restore IPC Default Configuration
Local IP Address:192.168.1.4
Subnet Mask:255.255.255.0 Gateway: 192.168.1.1
Modify Network Parameter
CE :98 :23 :75 :35 :22
Mac Address
IP Address
192 .168 . 1 . 201
255 . 255 . 255 . 0
Subnet Mask
192 .168 . 1 . 1
Gateway
Modify
The default username is admin; the default password is 123456.
● Direct Access Through WEB Browser
MENU
IPC
The default network settings are as shown below:
About
IP address: 192.168.226.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera
Modify
for the first time.
① Set the IP address of the PC and make sure the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click "Local Area Connection" to pop up
DNS：210.21.196.6
the following window. Select "Properties" and then select Internet
protocol according to the actual situation (for example: IPv4).
Next, click "Properties" button to set the network of the PC.
② Open a browser and enter the default address of IP-CAM
and confirm.
③ Download and run the plugin in the computer.
④ Enter the default username and password in the login interface
to log in.
Network Cable
MENU
Computer
HTTP:80
Data Port:9008
450043001057 A2