Epever LandStar LS101260LPLW Hızlı Kılavuz - Sayfa 2

Kontrolör Epever LandStar LS101260LPLW için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Epever LandStar LS101260LPLW 2 sayfaları. Solar charge controller with built-in led driver

Sayfayı Yazdır

Epever LandStar LS101260LPLW Hızlı Kılavuz

Timer3

LED Rated Current Percentage

Timer4/5

LED Rated Current Percentage

Timer6

LED Rated Current Percentage

※The default value can be changed according to the user requirement.

4)Time Control

Control the load on/off time by setting the real-time clock.

5) Intelligent Power Mode

When the battery voltage is lower than "Under Voltage Warning Recover Voltage (UVWR

adjustable)", the intelligent power mode is enabled; at this time, the LED current

percentage will be automatically reduced in linear with the voltage drop of battery. When

the battery voltage is lower than "Under Voltage Warning Voltage (UVW adjustable)", a

minimum LED current percentage (default 2%, adjustable) will be output. In addition, when

the battery voltage is higher than UVWR, the controller will exit the intelligent power mode.

NOTE：The load is ON when the controller power on 1seconds. After 1

seconds it will restore to set working mode.

NOTE：In the mode of Light ON/OFF and Light ON/Timer, the load is

turned on after 10Min. delay，the delay time can be set.

6. Setting Operation

There are two methods that it can realize controller work

mode and parameters through IR function:

1) 2.4G Remote Controller—RC11

This method can realize one-key setting operation which is

suitable for bulk quantity products setting or applied in the

projects.

2) Super Parameter Programmer—FC02

NOTE: Please refer to the user manual of handheld

device.

7. Protection

Protection

Conditions

PV Reverse

When the battery is correct connecting, the

Polarity

PV can be reversed.

Battery Reverse

When the PV is not connecting, the battery

Polarity

can be reversed.

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Battery

Temperature sensor is higher than 65℃

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the low-

Lithium battery

temperature value

Low Temperature

★

Temperature sensor is higher than the low-

temperature value

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuits, the output is OFF 10s;

Load Short

Three short circuits, the output is OFF 15s;

Circuit

Four short circuits, the output is OFF 20s;

Five short circuits, the output is OFF 25s;

Six short circuits, the output is OFF

Max. load voltage≥68V

One open circuit, the output is OFF 5s;

Two open t circuits, the output is OFF 10s;

Load Open

Three open circuits, the output is OFF 15s;

Circuit(Load over

Four open circuits, the output is OFF 20s;

voltage)

Five open circuits, the output is OFF 25s;

Six open circuits, the output is OFF5s;

Seven open circuits, the output is OFF5s

★Warning: If selecting a lithium battery, it must be set at low-temperature

value(LTV) according to the charging/discharging temperature of lithium

battery; otherwise, the lithium battery will be damaged.

8. Troubleshooting

Faults

Possible reasons

Charging LED

indicator off during

the daytime when

array disconnection

sunshine falls on PV

modules properly

Min.9V can start up the

No LED indicator

controller.

Battery LED

indicator green Fast

Battery over voltage

Flashing

Battery

Battery LED

indicator red

over discharged

Battery Status LED

indicator red

Battery Overheating

flashing

All the LED indicator

System voltage error

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

00:00—23:59H

50%

0—100%

00:00—23:59H

0—100%

00:00—23:59H

100%

0—100%

Status

The controller is not

damage

Stop charging

Stop discharging

Output is OFF

Output is ON

Stop charging or

discharge

Begin charging or

discharge

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle

(night time>3 hours).

Output is OFF

(Cycle to perform)

Troubleshooting

Confirm that PV and battery wire

connections are correct and tight

Measure battery voltage with

multi-meter. Min.9V can start up the

controller.

①Disconnect the solar array and

measure the battery voltage whether

is too high; ②Change the controller;

③ Change the battery

When the battery voltage is restored

to or above setpoint (low voltage

①

reconnect voltage), the load work

The controller will automatically stop

working. When the temperature is

below 50 º C, the controller will resume

working.

Check whether the battery voltage

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

flashing(battery red

indicator flashing)

①Unreliable wiring,

connection fails.

②The loading mode is

Power on normally,

wrong

③The controller does

the load is off

not match with the LED

light.

④Output short circuit

The controller does not

match with the LED

light source. This

The dimming

product is a step-up

function is invalid

current control, if the

input voltage is lower

than the rated voltage,

it is not working.

①When the battery is over-discharged, the battery indicator will be red, and the load will be

off all the time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV). In

order to judge the system is normal or not, firstly measuring the battery voltage whether is

more than LVRV, if not, restarting the controller to detect the load whether it is normal.

WARNING: The LVRV can be set, but must be more careful that it maybe

damages the battery if the LVRV is set too low.

9. Technical Specifications

Item

LS101240LPLW

Nominal system

voltage

Rated charge current

Max. PV open circuit

voltage

Battery input voltage range

Max. output power

40W

Max. output Current

2.6A

Output voltage range

Load open circuit voltage

Maximum output efficiency

Output current

control accuracy

Lead-acid battery: Sealed(default)/Gel/Flooded/User

Battery Type

Lithium battery:LiFePO4/Li-NiCoMn/User

Equalization Voltage▼ Sealed:14.6V; Flooded:14.8V;User:9-17V

Boost Voltage▼

Sealed:14.4V;Gel:14.2V;Flooded:14.6V;User:9-17V

Float Voltage▼

Sealed/Gel/Flooded:13.8V;User:9-17V

UVWR▼

Sealed/Gel/Flooded:12.2V;User:9-17V

UVW▼

Sealed/Gel/Flooded:12.0V;User:9-17V

Low Voltage

Sealed/Gel/Flooded:12.6V:User:9-17V

Recover Voltage▼

Low Voltage

Sealed/Gel/Flooded:11.1V:User:9-17V

Disconnect Voltage▼

Boost Voltage▼

LiFePO4(4s):14.5V/Li-NiCoMn(3s):12.5V/User:9-17V

UVWR▼

LiFePO4(4s):12.8V/Li-NiCoMn(3s):12.2V/User:9-17V

UVW▼

LiFePO4(4s):12.0V/Li-NiCoMn(3s):10.5V/User:9-17V

Low Voltage

LiFePO4(4s):12.8V/Li-NiCoMn(3s):10.5V/User:9-17V

Reconnect Voltage▼

Low Voltage

LiFePO4(4s):11.1V/Li-NiCoMn(3s):9.3V/User:9-17V

Disconnect Voltage▼

Self-consumption

Charge Circuit Voltage

Drop

Communication way

Communication distance

Working environment

temperature

Enclosure

Overall dimension(mm)

87x58x22.8

Mounting dimension(mm)

Mounting hole size(mm)

Power cable(AWG/mm

)

0.17kg

Net weight

◆ The controller is not recognized system voltage and no temperature

compensation when the battery connects the lithium battery.

▼The parameters are 12V system at 25 º C, please double the values in 24V system.

10. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of the controller.

 The controller is working temperature exceeds the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Any changes without prior notice!

matches the controller working

voltage. Please change to a suitable

battery or reset the working voltage

①Check the connecting cables

②Check the load mode and

parameter

③The voltage of LED-light source is

not in the output voltage range of

controller

④Check the connecting cables and

LED light source

①Replace the LED light

②Reduce system rated voltage grade

and replace the product model

For example, 24V system change to

12V system, and replace the

corresponding controller.

LS101260LPLW

LS102460LPLW

12VDC

12/24VDC◆ or Auto

10A

30V

50V

9～16V

9～32V

30W/12V

60W

60W/24V

4.0A

2.0A

(Max. Battery Voltage +2V)～60V

60V

96%

≤30mA

≤19mA(12V);≤35mA(24V)

≤0.17V

2.4G

≤20m

-40℃～+55℃

IP68(1.5m,72h)

87x63x24.8

108.5x118x25.6

Φ4

PV/BAT:14/2.5

LOAD:18/1.0

0.20kg

Version number：V1.0

LS2024120LPLW

20A

60W/12V

120W/24V

4.0A

100.5 x 76

Φ5

PV/BAT:12/4.0

LOAD:18/1.0

0.40kg