Epever LandStar LS102480GPLI Hızlı Kılavuz - Sayfa 2

Kontrolör Epever LandStar LS102480GPLI için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Epever LandStar LS102480GPLI 2 sayfaları. Solar charge controller with built in led driver of step-down voltage

Sayfayı Yazdır

Epever LandStar LS102480GPLI Hızlı Kılavuz

Item

Mode1

LED Rated Current

Time1

LED Rated Current Percentage

100%

Time2

LED Rated Current Percentage

80%

Time3

LED Rated Current Percentage

50%

4) Real-time Control

Control the load ON/OFF time through setting real-time clock.

5）Battery under voltage control

When the battery under voltage, the controller will reduce the LED rated

current percentage for charging automatically. Return to normal mode when

recovery from under voltage.

NOTE：The load is ON when the controller power on 10seconds. After 10

seconds it will restore to set working mode.

NOTE：In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 10Min. delay，the delay time can be set.

8. Protection

Protection

Battery straight polarity and PV reverse

PV Reverse Polarity①

polarity

Battery Reverse

LED lights straight polarity and battery

reverse polarity

Polarity②

Battery Over Voltage

The battery voltage reaches to the OVD

Battery Over Discharge

The battery voltage reaches to the LVD

Temperature sensor is higher than 65℃

Battery Overheating

Temperature sensor is less than55℃

Load current ≥4 times rated current

Load Short Circuit

Clear the fault: Restart the controller or

(5 times reconnect

wait for one night-day cycle (night time>3

load)

hours).

①WARNING: The controller will be damaged when battery reverse polarity

and PV reverse polarity!

②WARNING: The controller will be damaged when battery reverse polarity

and PV straight polarity!

9. Troubleshooting

Faults

Possible reasons

Charging LED

indicator(or LCD)

off during daytime

PV array

when sunshine falls

disconnection

on solar modules

properly

Wire connection is

correct, the

Battery voltage

controller is not

maybe less than 8V

working

Battery LED

indicator green fast

Battery over voltage

flashing

Battery LED

Battery over

indicator red color

discharged

Battery LED

indicator red slowly

Battery Overheating

flashing

①The connecting

wires are error or

virtually connected

②Load mode is not

Powering on

normally, the LED

appropriate.③This

is off

controller does not

match with the LED

light.④Output short

circuit.

The controller does

The dimming

not match with the

function is invalid

LED light source.

10. Technical Specifications

Item

Nominal system voltage

Rated charge current

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

Default

Range

Mode2

LS102480GPLI:0-4A(12V/24V)

0.35A

LS2024100GPLI:0-5A(12V/24V)

00:00—23:59H

100%

0—100%

00:00—23:59H

50%

0—100%

00:00—23:59H

100%

0—100%

Conditions

The controller is

not damage

Stop charging

stop discharging

Output is OFF

Output is ON

Output is OFF

Output is ON

Troubleshooting

Confirm that PV and battery

wire connections are correct

and tight

Measure battery voltage with

the multi-meter. Min.8V can

start up the controller

Check if battery voltage is

higher than OVD, and

disconnect the PV

When the battery voltage is

restored to or above LVR point

(low voltage reconnect

voltage), the load will recover

The controller will

automatically turn the system

off. But while the temperature

decline to be below 55 º C, the

controller will resume.

①Check the connecting cable.

② Check the load's mode and

parameters.③The voltage of

LED light is not within the

output voltage range of

controller.④Check the

connecting cables and LED

light.

This product is a step-down

voltage control, If input voltage

is higher than the Load output

voltage, it is not working.

Replace the LED light.

LS102480GPLI

LS2024100GPLI

12/24VDC Auto

10A

20A

Tel: +86-10-82894112 / 82894962

Max. PV open circuit

voltage

Battery input voltage

range

Max. output power

Max. output current

Max. output voltage

Max. output efficiency

Output current control

accuracy

Battery Type

Communication

Communication distance

Communication angle

Self-consumption

Charge Circuit Voltage

Drop

Temperature

compensation

coefficient

Working environment

temperature

Enclosure

Status

Overall dimension

Mounting dimension

Mounting hole size

Power cable

Net weight

Battery Voltage Control Parameters

Below parameters are in 12V system at 25 º C, please double the values in

24V system

Battery Type

Over Voltage Disconnect

Voltage

Charging Limit Voltage

Over Voltage Reconnect

Voltage

Equalize Charging

Voltage

Boost Charging Voltage

Float Charging Voltage

Boost Reconnect

Charging Voltage

Low Voltage Reconnect

Voltage

Under Voltage Warning

Reconnect Voltage

Under Voltage Warning

Voltage

Low Voltage Disconnect

Voltage

Discharging Limit Voltage

Equalize Duration

Boost Duration

NOTE:1) The default battery type is Sealed, For Sealed, Gel, Flooded

battery type, the voltage point is fixed, unable to be modified. The

adjusting range of equalize duration is 0 to180min and boost duration is

10 to180min.

2) User type is the user defined battery type. The default value is the

same as sealed type. When modify it, please follow the below logistic

relation:

a ) Over Voltage Disconnect Voltage＞Charging Limit Voltage ≥Equalize

Charging Voltage ≥Boost Charging Voltage ≥ Float Charging Voltage ＞

Boost Reconnect Charging Voltage.

b ) Over Voltage Disconnect Voltage＞Over Voltage Reconnect Voltage.

c) Low Voltage Reconnect Voltage＞Low Voltage Disconnect Voltage ≥

Discharging Limit Voltage.

d ) Under Voltage Warning Reconnect Voltage＞Under Voltage Warning

Voltage ≥ Discharging Limit Voltage.

e ) Boost Reconnect Charging voltage＞Low Voltage Disconnect Voltage.

11. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Website:www.epsolarpv.com/www.epever.com

40W/12V,80W/24V

4A/12V, 24V

Min. V

-0.5V

BAT

Sealed / Gel / Flooded / User

≤16mA(12V)；≤20mA (24V)

-3mV/℃/2V

-35℃～+55℃

IP68(1.5m，72h)

107x68x20mm

100mm

Φ4

PV/BAT:14AWG(2.5mm

LOAD: 18AWG(1.0mm

0.25kg

Sealed

Gel

16.0V

15.0V

——

14.6V

14.4V

14.2V

13.8V

13.2V

12.6V

12.2V

12.0V

11.1V

10.6V

——

120 min.

Any changes without prior notice! Version number：V1.0

50V

8V～32V

50W/12V,100W/24V

5A/12V,24V

Min. V

-1V

BAT

96%

≤50mA

≤6m

≤15°

≤0.16V

108.5x88x25.6mm

100.5mm

Φ5

)

PV/BAT:12AWG(4.0mm

)

LOAD: 18AWG(1.0mm

)

0.39kg

Flooded

User

16.0V

9～17V

15.0V

9～17V

15.0V

9～17V

14.8V

9～17V

14.6V

9～17V

13.8V

9～17V

13.2V

9～17V

12.6V

9～17V

12.2V

9～17V

12.0V

9～17V

11.1V

9～17V

10.6V

9～17V

120 min. 0～180 min.

120 min. 10～180 min.