Epever Tracer BP Series Manuel - Sayfa 2

Kontrolör Epever Tracer BP Series için çevrimiçi göz atın veya pdf Manuel indirin. Epever Tracer BP Series 2 sayfaları. Mppt solar charge controller
Ayrıca Epever Tracer BP Series için: Manuel (2 sayfalar)

Sayfayı Yazdır
Epever Tracer BP Series Manuel
※MT50 does not support the relevant parameters of lithium battery.
※Specific instructions refer to the list of accessories and software.

8. Protection

 PV Over Current
The controller will limit battery charging current to the Maximum Battery Current
rating. Therefore an over-sized solar array will not operate at peak power.
 PV Short Circuit
When PV short circuit is powered on or PV input is short circuit on low-power, the
controller will stop charging. Clear it to resume normal operation.
WARNING: The controller may be damaged, when PV input is short
circuit on high-power.
 PV Reverse Polarity
Fully protection against PV reverse polarity, correct the wire connection to resume
normal operation.
WARNING: Controller will be damaged when the PV array straight
polarity and the actual operation power of the PV array is 1.5 times
greater than the rated charge power!
 Battery Reverse Polarity
Fully protection against battery reverse polarity, correct the wire connection to
resume normal operation.
 Battery Over Voltage
When the battery voltage reaches to the set point of Over Voltage Disconnect Voltage,
the controller will stop charging the battery to protect the battery from being over
charged to break down.
 Battery Over Discharge
When the battery voltage reaches to the set point of Low Voltage Disconnect Voltage,
the controller will stop discharging the battery to protect the battery from being over
discharged to break down.
 Battery Overheating
The controller detects the environment temperature through the external temperature
sensor. If the environment temperature exceeds 65 º C, the controller will automatically
start the overheating protection to stop working, and recover below 55 º C.
 Lithium battery Low Temperature
The temperature sensor is less than the low temperature value, Lithium battery stop
charging/discharging. It is higher than the low temperature value, Lithium battery start
charging/discharging.
 Load Overload
If the load current exceeds the maximum load current rating 1.05 times, the controller
will disconnect the load. Overloading must be cleared up through reducing the load
and restarting controller.
 Load Short Circuit
Load will be switched off when load short circuit (≥4 times rated current) happens.

9. Technical Specifications

Item
Model
Tracer2606BP
Nominal system voltage
Battery input voltage range
Rated charge/discharge
current
Rated charge power
130W/12V;260W/24V 200W/12V;400W/24V 260W/12V;520W/24V 130W/12V;260W/24V 200W/12V;400W/24V 260W/12V;520W/24V 390W/12V;780W/24V
60V( at minimum operating environment temperature ）
Max. PV open circuit voltage
MPP Voltage range
Battery Type
Equalize Charging
Voltage
Boost Charging
Voltage
Float Charging Voltage
Low Voltage Reconnect
Voltage
Low Voltage
Disconnect Voltage
Boost Charging Voltage
Low Voltage
Reconnect Voltage
Low Voltage
Disconnect Voltage
Self-consumption
Temperature
compensation coefficient
Communication
Working environment Tem.
Enclosure
Overall dimension
124×89×30mm
Mounting hole size
Mounting dimension
88×76mm
Power cable
Net weight
HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Tracer3906BP
12/24VDC Auto( Lithium battery do not automatic identification system voltage)
10A
15A
46V( at 25℃ environment temperature )
( Battery voltage+2V)～36V
Lead-acid battery: Sealed(Default) / Gel / Flooded/User; Lithium battery:LiFePO4/ Li-NiCoMn/User
Sealed :14.4V/Gel：14.2V/Flooded:14.6V/User:9-17V (×2/24V)
-3mV/℃/2V( Lithium battery don't have temperature compensation coefficient)
150×93.5×32.7mm
120×83mm
2
14AWG(2.5mm
)
0.54kg
0.74kg
1
Tel：+86-10-82894896 / 82894112/+86-752-3889706
Controller will automatically attempt to reconnect load for 5 times. If short circuit
protection still exist after controller's 5 times attempts, user have to clear short
circuit ,then restart the controller or wait for one night-day cycle (night time>3 hours).
 Temperature sensor break down
If the temperature sensor short-circuited or damaged, the controller will be charging
or discharging at the default temperature 25 º C to prevent the battery damaged from
overcharging or over discharged.
High Voltage Transients
The controller is protected against small high voltage transients. In lightning prone
areas, additional external suppression is recommended.

10. Troubleshooting

Faults
LED Charging
indicator turn off
during daytime
when sunshine falls
on PV modules
properly
No LED indicator
Battery LED
indicator green fast
Flashing
Battery LED
indicator red
Battery LED
indicator red
flashing
Load is not output
①When it is overload or short circuit, the load have 5 times auto-recovery output
function, which each times delay respectively 5s, 10s, 15s, 20s, 25s.
11. Disclaimer
This warranty does not apply under the following conditions:
 Damage from improper use or use in an unsuitable environment.
 PV or load current, voltage or power exceeding the rated value of controller.
 The controller is working temperature exceed the limit working environment
temperature.
 User disassembly or attempted repair the controller without permission.
 The controller is damaged due to natural elements such as lighting.
 The controller is damaged during transportation and shipment.
Tracer5206BP
Tracer2610BP
8.5～32VDC
20A
10A
100V( at minimum operating environment temperature ）
Sealed :14.6V/Gel：No / Flooded:14.8V/User:9-17V (×2/24V)
Sealed/Gel/Flooded:13.8V/User:9-17V (×2/24V)
Sealed/Gel/Flooded:12.6V/User:9-17V (×2/24V)
Sealed/Gel/Flooded:11.1V/User:9-17V (×2/24V)
LiFePO4:14.5V/ Li-NiCoMn:12.5V / User:9-17V (×2/24V)
LiFePO4:12.8V / Li-NiCoMn:10.5V / User:9-17V (×2/24V)
LiFePO4:11.1V / Li-NiCoMn:9.3V / User:9-17V (×2/24V)
≤13mA/12V;≤11.5mA/24V
RS485
-40℃～+60℃
IP67
153×105×52.1mm
124×89×30mm
Φ3.5mm
120×94mm
88×76mm
2
12AWG(4mm
)
14AWG(2.5mm
1.20kg
0.54kg
Website：www.epever.com
Possible reasons
Troubleshooting
PV
Confirm that PV and battery wire
array disconnection
connections are correct and tight
Measure battery voltage with the
Battery voltage maybe
multi-meter. Min.8.5V can start up
less than 8.5V
the controller
Check if battery voltage is higher
Battery over voltage
than OVD, and disconnect the PV
When the battery voltage is restored
Battery
to or above LVR point (low voltage
over discharged
reconnect voltage), the load will
recover
The controller will automatically turn
the system off. But while the
Battery Overheating
temperature decline to be below 50
º C, the controller will resume.
①Please reduce the number of
electric equipments.
①
②Restart the controller.
Load Overload
③wait for one night-day cycle (night
time>3 hours).
①Check carefully loads connection,
clear the fault.
①
②Restart the controller.
Load Short Circuit
③wait for one night-day cycle (night
time>3 hours).
Tracer3910BP
Tracer5210BP
15A
20A
92V( at 25℃ environment temperature )
( Battery voltage+2V)～72V
150×93.5×32.7mm
153×105×52.1mm 153.3×105×52.1mm
120×83mm
120×94mm
2
2
)
12AWG(4mm
0.74kg
1.20kg
Any changes without prior notice! Version number：V2.2
2
Tracer7810BP
30A
-40℃～+50℃
2
)
10AWG(6mm
)
1.26kg