Epever Tracer2606BP Manuel

Kontrolör Epever Tracer2606BP için çevrimiçi göz atın veya pdf Manuel indirin. Epever Tracer2606BP 2 sayfaları. Solar charge controller
Ayrıca Epever Tracer2606BP için: Manuel (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)

Sayfayı Yazdır

※Thank you for selecting the Tracer BP series MPPT solar charge

controller. Please read this manual carefully before using the

product and pay attention to the safety information.

Tracer BP series

---

1.Safety Information

 Read all of the instructions in the manual before installation.

 DONOT disassemble or attempt to repair the controller.

 Install external fuse or breaker as required.

 Do disconnect the solar module and fuse/ breakers near to battery before installing

or moving the controller.

 Power connections must remain tight to avoid excessive heating from a loose

connection.

 Only charge batteries that comply with the parameters of controller.

 Battery connection may be wired to one battery or a bank of batteries.

 Risk of electric shock, the PV and load can produce high voltages when the

controller is working.

2. Overview

The Tracer BP series solar charge controller adopt to the advanced Maximum Power

Point Tracking charging methods, it enables the system charging and discharging

management to obtain the most radical optimization. Increase the system flexibility, yet

lower down the system cost. The controller support a variety of battery, for example

sealed, gel, flooded and lithium battery. User can view and modify the working status

and parameters. It can be widely used on solar home system, traffic signal, solar street

light, solar garden lamp, etc. The features are listed below:

 Adopt high quality components of ST,IR and Infineon, make sure product using

lifespan

 Wide working environment temperature

 Apply to lead-acid battery and lithium battery

 Lithium battery self-activating and low temperature protection function

 Maximum conversion efficiency of 98%

 Advanced Maximum Power Point Tracking (MPPT) technology, with tracking

efficiency no less than 99%

 Ultra-fast tracking speed and guaranteed tracking efficiency

 Accurately recognizing and tracking of multiple power points

 PV power limitation function

 Monitoring and setting parameter via Mobile APP, PC Monitor setting software with

RS485 communication interface.

 Use of standard Modbus communication protocol for RS485 bus connections,

communication protocol compatibility much better

 Connecting the IOT(Internet of Things) module and Cloud Server monitoring software

to realize remote monitoring of the multi-machine system

 The RS485 connector can provide power supply

 Aluminum housing for better cooling

 Real-time energy statistics function

 IP67 waterproof degree

3. Product Features

⑴

①

Temperature Sensor

②

PV Positive and Negative Wires

③

Battery Positive and Negative Wires

④

Load Positive and Negative Wires

⑴The temperature sensor short-circuited or damaged, the controller will be

charging or discharging at the default temperature 25 º C.

⑵The port can provide the DC power supply of 5VDC/150mA and have the short

circuit function.

NOTE: When the RS485 communication port is not working, the

waterproof cap must be installed to prevent water getting in.

4. Wiring

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

MPPT Solar Charge Controller

⑤

Charging Status LED indicator

⑥

Battery Status LED indicator

⑦

RS485 waterproof port

⑧

Waterproof cap(Included)

Tel：+86-10-82894896 / 82894112/+86-752-3889706

 Connection Order

1) Connect components to the charge controller in the sequence as shown above and

pay much attention to the "+" and "-".Please don't insert the fuse or turn on the breaker

during the installation. When disconnecting the system, the order will be reserved.

2) After power on the controller, check the battery LED indicator on the controller, it will

be green. If it's not green, please refer to chapter 10.

3) Connect a fuse in series through battery positive (+) in the circuit and the battery

circuit fuse must be 1.25 to 2 times to the rated current. The installed distance is within

150mm.

 Load self-test function

The load is ON when the controller power on 10s. After 10s it will restore to set working

mode.

5. LED Indicators

Indicator

Charging(green) and battery

indicator(orange)flashing simultaneously

※When the battery type is Lithium Battery，the controller do not recognize the

system voltage automatically.

6.Load Working Mode

1) Manual Mode(Default ON)

2) Light ON/OFF

3) Light ON+ Timer

4) Real-time Control

⑵

Control the load ON/OFF time through setting real-time clock.

NOTE: In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 10Min. delay.

7. Accessories(optional) and Software

1）PC Software

www.epever.com ——Solar Station Monitor

2）APP Software

 Android phone

www.epever.com——ChargeController(Li)

 IPhone

APP Store——EPEVER——EP-01

Website：www.epever.com

Color

Status

PV connection normal

but low

Green

On Solid

voltage(irradiance)

from PV, no charging

No PV voltage(night

time) or PV connection

Green

OFF

problem

Green

Slowly Flashing(1Hz)

In charging

Green

Fast Flashing(4Hz)

PV Over voltage

Green

On Solid

Normal

Green

Slowly Flashing(1Hz)

Full

Green

Fast Flashing(4Hz)

Over voltage

Orange

On Solid

Under voltage

Red

On Solid

Over discharged

Battery Overheating

Red

Fast Flashing(4Hz)

Low temperature

System voltage error※

Instruction