Epever Tracer2610BP Manuel - Sayfa 2

Kontrolör Epever Tracer2610BP için çevrimiçi göz atın veya pdf Manuel indirin. Epever Tracer2610BP 2 sayfaları. Solar charge controller
Ayrıca Epever Tracer2610BP için: Manuel (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)

Sayfayı Yazdır

Accessory 1: Fixed Plate (Four)

Overall dimension：20×18×6mm/Mounting hole size：Φ3.5mm

Accessory 2: Wireless collector (eBox-WL433M-01)

Accessory 3: Super Parameter Programmer—SPP-02 and Remote Meter-MT50

Use USB to RS485 converter cable: CC- RS485-RS485-150U-22AWG

Accessory 4: PC monitoring setting software "Solar Station Monitor"

 Use USB to RS485 converter cable: CC-USB-RS485-150U-22AWG

Accessory 5: Mobile APP

 Use USB to RS485 converter cable: CC-USB-RS485-150U-22AWG

 Use OTG cable: OTG-12CM

 APP software can be downloaded from the website of http://www.epsolarpv.com.

Note: Accessory 3-5 can set parameters of the controller. Please refer to the user

manual of accessory.

8. Protection

 PV Over Current

The controller will limit battery charging current to the Maximum Battery Current

rating. Therefore an over-sized solar array will not operate at peak power.

 PV Short Circuit

When PV short circuit is powered on or PV input is short circuit on low-power, the

controller will stop charging. Clear it to resume normal operation.

WARNING: The controller may be damaged, when PV input is short

circuit on high-power.

 PV Reverse Polarity

Fully protection against PV reverse polarity, correct the wire connection to resume

normal operation.

WARNING: Controller will be damaged when the PV array straight

polarity and the actual operation power of the PV array is 1.5 times

greater than the rated charge power!

 Battery Reverse Polarity

Fully protection against battery reverse polarity, correct the wire connection to

resume normal operation.

 Battery Over Voltage

When the battery voltage reaches to the set point of Over Voltage Disconnect Voltage,

the controller will stop charging the battery to protect the battery from being over

charged to break down.

 Battery Over Discharge

When the battery voltage reaches to the set point of Low Voltage Disconnect Voltage,

the controller will stop discharging the battery to protect the battery from being over

discharged to break down.

 Battery Overheating

The controller detects the environment temperature through the external temperature

sensor. If the environment temperature exceeds 65 º C, the controller will automatically

start the overheating protection to stop working, and recover below 55 º C.

 Lithium battery Low Temperature

The temperature sensor is less than the low temperature value, Lithium battery stop

charging/discharging. It is higher than the low temperature value, Lithium battery start

charging/discharging.

 Load Overload

If the load current exceeds the maximum load current rating 1.05 times, the controller

will disconnect the load. Overloading must be cleared up through reducing the load

and restarting controller.

 Load Short Circuit

Load will be switched off when load short circuit (≥4 times rated current) happens.

Controller will automatically attempt to reconnect load for 5 times. If short circuit

10. Technical Specifications

Item

Model

Nominal system voltage

Battery input voltage range

Rated charge current

Rated charge power

①

Max. PV open circuit voltage

MPP Voltage range

Battery Type

Equalize Charging Voltage

Boost Charging Voltage

Float Charging Voltage

Low Voltage

Reconnect Voltage

Low Voltage

Disconnect Voltage

Self-consumption

Temperature compensation

coefficient

Communication

Working environment

temperature

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

※The parameters are 12V system at 25 º C, please double the values in 24V system.

＃Lithium battery do not automatic identification system voltage and no temperature compensation coefficient.

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

Tracer2606BP

Tracer3906BP

10A

15A

130W/12V

195W/12V

260W/24V

390W/24V

60V( at minimum operating environment temperature ）

46V( at 25℃ environment temperature )

( Battery voltage+2V)～36V

Sealed :14.4V/Gel：14.2V/Flooded：14.6V※; LiFePO4:14.6V/ Li-NiCoMn:12.51V / User:9-34V

Sealed/Gel/Flooded:13.8V※ ; LiFePO4:14.4V / Li-NiCoMn:12.39V / User:9-34V

Sealed/Gel/Flooded:12.6V※ ; LiFePO4:12.0V / Li-NiCoMn:10.8V / User:9-34V

Sealed/Gel/Flooded:11.1V※ ; LiFePO4:10.6V / Li-NiCoMn:9.3V / User:9-34V

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT/LOAD:14AWG(2.5mm

0.54kg

0.74kg

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

protection still exist after controller's 5 times attempts, user have to clear short

circuit ,then restart the controller or wait for one night-day cycle (night time>3 hours).

 Temperature sensor break down

If the temperature sensor short-circuited or damaged, the controller will be charging

or discharging at the default temperature 25 º C to prevent the battery damaged from

overcharging or over discharged.

 High Voltage Transients

The controller is protected against small high voltage transients. In lightning prone

areas, additional external suppression is recommended.

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine falls

on PV modules

properly

No LED indicator

Battery LED

indicator green fast

Flashing

Battery LED

indicator red

Battery LED

indicator red

flashing

Load is not output

①When it is overload or short circuit, the load have 5 times auto-recovery output

function, which each times delay respectively 5s, 10s, 15s, 20s, 25s.

11. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer5206BP

Tracer2610BP

12/24VDC Auto

＃

9～32VDC

20A

260W/12V

520W/24V

Sealed(Default) / Gel / Flooded ; LiFePO4/ Li-NiCoMn/User

Sealed :14.6V/Gel：No / Flooded：14.8V※; No

≤13mA/12V;≤11.5mA/24V

-3mV/℃/2V

＃

RS485

-40℃～+60℃

IP67

153×105×52.1mm

124×89×30mm

Φ3.5mm

120×94mm

)

1.20kg

Possible reasons

Confirm that PV and battery wire

array disconnection

connections are correct and tight

Measure battery voltage with the

Battery voltage maybe

multi-meter. Min.9V can start up the

less than 9V

controller

Check if battery voltage is higher

Battery over voltage

than OVD, and disconnect the PV

When the battery voltage is restored

Battery

to or above LVR point (low voltage

over discharged

reconnect voltage), the load will

recover

The controller will automatically turn

the system off. But while the

Battery Overheating

temperature decline to be below 50

º C, the controller will resume.

①Please reduce the number of

electric equipments.

①

②Restart the controller.

Load Overload

③wait for one night-day cycle (night

time>3 hours).

①Check carefully loads connection,

clear the fault.

①

②Restart the controller.

Load Short Circuit

③wait for one night-day cycle (night

time>3 hours).

Any changes without prior notice! Version number：V1.0

Tracer3910BP

10A

15A

130W/12V

195W/12V

260W/24V

390W/24V

100V( at minimum operating environment temperature ）

92V( at 25℃ environment temperature )

( Battery voltage+2V)～72V

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT/LOAD:12AWG(4mm

0.54kg

0.74kg

Troubleshooting

Tracer5210BP

20A

260W/12V

520W/24V

153×105×52.1mm

120×94mm

)

1.20kg