Epever Tracer3906BPL Hızlı Başlangıç Kılavuzu
Kontrolör Epever Tracer3906BPL için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Epever Tracer3906BPL 3 sayfaları. Mppt solar charge controller with built-in led driver
Ayrıca Epever Tracer3906BPL için: Hızlı Kılavuz (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)
Sayfayı Yazdır
HUIZHOU EPEVER TECHNOLOGY CO., LTD.
※Thank you for selecting the Tracer BPL series lithium battery
MPPT solar charge controller with built-in LED driver. Please read
this manual carefully before using the product and pay attention to
the safety information.
MPPT Solar Charge Controller
1. Overview
The Tracer BPL series lithium battery MPPT solar charge controller combines solar
charge controller and LED constant current driver into one unit. It is ideal for solar LED
lighting, especially when a dimmer function is needed. The advanced Maximum Power
Point Tracking charging methods enables the system charging and discharging
management to obtain the most radical optimization. Increase the system flexibility, yet
lower down the system cost. The features are listed below:
Adopt high-quality components of ST, IR, and Infineon, ensure products' lifespan
Wide working environment temperature(-40℃~60℃)
Apply to lead-acid battery and lithium battery
Lithium battery self-activating and low-temperature protection function
The maximum conversion efficiency of 98%
Advanced Maximum Power Point Tracking (MPPT) technology, with tracking
efficiency no less than 99.5%
Accurately recognizing and tracking of multiple power points
Lithium battery low-temperature protection function
Lithium battery limit current in low temperature
Digital precision constant current control and the control accuracy are less than ±2%
Intelligent power reduction mode with a 365-day lighting control technology
Maximum output efficiency of 96%
PV and Load power limitation function
The output current can be adjusted among the rated power and current range
Monitoring and setting parameters via Mobile APP, the PC software.
Standard Modbus communication protocol for RS485 bus connections, to offer a
better communication protocol compatibility
Connecting the IoT(Internet of Things) module and Cloud Server monitoring software
to realize remote monitoring of the multi-machine system
The RS485 connector can provide a power supply
Aluminum housing for better cooling
Real-time energy statistics function
IP67 waterproof degree
2. Product Features
⑴
①
Temperature Sensor
②
PV Positive and Negative Wires
③
Battery Positive and Negative Wires
④
Load Positive and Negative Wires
(1)The temperature sensor is short-circuited or damaged. The controller will be charging
or discharging at the default temperature of 25 ºC.
(2)The port can provide the DC power supply of 5VDC/150mA and have the short circuit
function.
NOTE: When the RS485 communication port is not working, the waterproof cap
must be installed to prevent water from getting in.
3. Wiring
⚫ Reference for Serial connection of LED
System
Serial
Voltage
connection
5～18 LED
12V
10～18 LED
24V
NOTE: The above one LED (1W, 3.3V) is calculated. If the user uses the
unconventional LED, The actual LED voltage must less than the Max. Load
Output Voltage.
WARNING：Caution electricity! With the product's built-in boost LED driver, the
output voltage is higher than the human safety voltage.
⚫ Connection Order
1) Connect components to the charge controller in the sequence as shown above and
pay much attention to the "+" and "-." Please don't insert the fuse or turn on the breaker
---with built-in LED Driver
⑤
Charging Status LED indicator
⑥
Battery Status LED indicator
⑵
⑦
RS485 waterproof port
⑧
Waterproof cap(Included)
Min. Output
Max. Output
Voltage
Voltage
15V
60V
30V
60V
1
Tel：+86-10-82894896/82894112/+86-752-3889706
during the installation. When disconnecting the system, the order will be reserved.
2) After powering the controller, check the battery LED indicator on the controller. It will
be green. If it's not green, please refer to chapter 9.
3) Connecting a fuse in series through battery positive (+) in the circuit and the battery
circuit fuse must be 1.25 to 2 times to the rated current. The installed distance is within
150mm.
4) The charging and discharging process can't be operated simultaneously, and the
discharge process should be operated before charging.
⚫ Load self-test function
The load is ON when the controller power on for 10seconds. After 10 seconds, it will
restore to set working mode.
4. LED Indicators
Indicator
Color
Green
On Solid
Green
OFF
Green
Slowly Flashing(1Hz)
Green
Fast Flashing(4Hz)
Green
On Solid
Green
Slowly Flashing(1Hz)
Green
Fast Flashing(4Hz)
Orange
On Solid
Red
On Solid
Red
Fast Flashing(4Hz)
All
Orange
Flashing two times
indicators
and green
5. Load Working Mode
1) Manual Mode
2) Light ON/OFF(Default)
3) Light ON + Timer
Light ON + Timer1
Light ON + Timer2
Light ON + Timer3
4) Real-time Control
Control the load ON/OFF time by setting a real-time clock.
5) Intelligent Power Reduction Mode
When the battery voltage is reduced to the "Reduce Power Start Voltage (adjustable),"
the intelligent power reduction mode is enabled. The LED output current is automatically
reduced in linear with the battery's voltage drop. When the battery voltage is reduced to
the "Reduce Power End Voltage (adjustable)," the LED output current is 2% of the rated
load current. The minimum percentage can be set to 1%. Also, when the battery voltage
is higher than "Reduce Power Start Voltage," the controller exits the intelligent power
reduction mode.
NOTE：In the mode of Light ON/OFF and Light ON/Timer, the load is turned on
after a 1-minute delay, the delay time can be set.
NOTE：The controller's real-time clock is an analog clock; it is valid at power-on
and invalid after power-off. When using the time mode, the clock needs to be
calibrated by handheld devices. The controller cannot be powered off after
calibration.
6. Optional accessories and Software
1）PC Software(www.epever.com ——Solar Station Monitor)
2）APP Software
Android phone(www.epever.com——ChargeController(Li) )
IPhone(APP Store——EPEVER——EP-01)
※MT50 does not support the relevant parameters of the lithium battery.
Website：www.epever.com
Status
Instruction
PV connection normal but
low voltage(irradiance)
from PV, no charging
No PV voltage(night time)
or PV connection problem
In charging
PV overvoltage
Normal
Full
Overvoltage
Under voltage
Over discharged
Low temperature
Battery Overheating
Set parameters
successfully
Turn-On voltage (Adjustable):
5V(12Vsystem),delay10min.
Turn-Off voltage (Adjustable):
6V(12Vsystem),delay10min.
Note:24V system voltage×2
2