Epever Tracer3910BP Hızlı Başlangıç Kılavuzu
Kontrolör Epever Tracer3910BP için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Epever Tracer3910BP 2 sayfaları. Lithium battery mppt solar charge controller
Ayrıca Epever Tracer3910BP için: Manuel (2 sayfalar), Manuel (2 sayfalar)
Sayfayı Yazdır
HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Thank you for selecting the Tracer BP MPPT solar charge
controller. Please read this manual carefully before using the
product and pay attention to the safety information.
MPPT Solar Charge Controller
1. Safety Information
Read all the instructions before installation.
DO NOT disassemble or attempt to repair the controller.
Install external fuse or breaker as required.
Disconnect the solar module and fuse/ breakers near to battery before installing or
moving the controller.
Power connections must remain tight to avoid excessive heating from a loose
connection.
Only batteries that comply with the controller's parameters can be charged.
Battery connection may be wired to one battery or a bank of batteries.
Risk of electric shock, the PV and load may produce high voltages when the
controller is running.
2. Overview
The Tracer BP solar charge controller adopts the advanced Maximum Power Point
Tracking charging technology. Increase the system charging efficiency, yet lower down
the system cost. The controller supports various batteries, for example, sealed, gel,
flooded, and lithium battery. Users can view and modify the operational status and
parameters. It can be widely used in a solar home system, traffic signal, solar street light,
solar garden lamp, etc. The features are listed below:
Adopt high-quality components of ST, IR, and Infineon to ensure product lifespan
Wider working environment temperature
Apply to lead-acid battery and lithium battery
Lithium battery self-activating and low-temperature protection function
The maximum conversion efficiency of 98%
Advanced Maximum Power Point Tracking (MPPT) technology, with tracking
efficiency no less than 99%
Accurately recognizing and tracking of multiple power points
PV power limitation function
Monitoring and setting parameters via Mobile APP, PC software
Adopt standard Modbus communication protocol for RS485 bus connections to get
better communication protocol compatibility
Connecting the IoT(Internet of Things) module and Cloud Server monitoring software
to realize remote monitoring
The RS485 connector can provide a power supply
Aluminum housing for better cooling
Real-time energy statistics function
IP68 waterproof degree
3. Product Features
Tracer26**/39**BP
⑴
①
Temperature Sensor
②
PV Positive and Negative Wires
③
Battery Positive and Negative Wires
④
Load Positive and Negative Wires
⑴ If the temperature sensor is short-circuited or damaged, the controller shall be
charging or discharging at the default temperature of 25º C.
⑵ The port can provide a DC power supply of 5VDC/150mA and own the short circuit
function.
When the RS485 communication port is not working, the waterproof
cap must be installed to prevent water from getting in.
CAUTION
4. Wiring
Tracer52**/7810BP
⑤
Charging Status LED indicator
⑥
Battery Status LED indicator
⑵
⑦
RS485 waterproof port
⑧
Waterproof cap(Included)
1
Tel：+86-10-82894896/82894112/+86-752-3889706
Connection sequence
1) Connect components to the controller in the sequence ① > ② > ③ as shown
above and pay much attention to the "+" and "-." Please don't insert the fuse or turn on
the breaker during the installation. When disconnecting the system, the order will be
reserved.
2) After powering the controller, the battery LED indicator on the controller shall flash
green. If it's not green, please refer to chapter 10, Troubleshooting.
3) Connect a fuse in series through battery positive (+) in the circuit. The battery circuit
fuse must be 1.25 to 2 times the rated current. The installed distance is within 150mm.
Load self-test function
The load is automatically turned ON after powering on the controller for 10s. After the
load keeps ON status for 10s, the controller restores to the set working mode.
5. LED Indicators
Indicator
Color
Green
Fast Flashing(4Hz)
Green
Fast Flashing(4Hz)
Orange
Red
Fast Flashing(4Hz)
Charging indicator(green) and battery
indicator(orange) flashing simultaneously
※When the battery type is a lithium battery, the controller does not recognize the
system voltage automatically.
6. Load Working Mode
1) Manual Mode(Default ON)
2) Light ON/OFF
3) Light ON+ Timer
4) Real-time Control
Control the load ON/OFF time by setting a real-time clock.
In the mode of Light ON/OFF and Light ON/Timer, the Load is turned
on after 10Min. Delay.
CAUTION
7. Accessories(optional) and Software
1）PC Software
www.epever.com ——Solar Station Monitor
2）APP Software
Android phone
www.epever.com——ChargeController(Li)
iPhone
APP Store——EPEVER——EP-01
※MT50 does not support the relevant parameters of the lithium battery.
Website：www.epever.com
Status
Instruction
PV connection normal but low
voltage(irradiance) from PV,
On Solid
no charging
No PV voltage(night time) or
OFF
PV connection problem
Slowly
In charging
Flashing(1Hz)
PV overvoltage
On Solid
Battery is normal
Slowly
Battery charges full
Flashing(1Hz)
Battery overvoltage
On Solid
Battery under voltage
On Solid
Battery over-discharged
Battery overheating
Lithium
battery
temperature
System voltage error※
Turn-On voltage (Adjustable):
5V(12Vsystem),delay10min.
Turn-Off voltage (Adjustable):
6V(12Vsystem),delay10min.
Note:24V system voltage×2
2
low