Epever Tracer3910LPLI Hızlı Kılavuz - Sayfa 2

Kontrolör Epever Tracer3910LPLI için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Epever Tracer3910LPLI 2 sayfaları. Solar charge controller with built in led driver

Sayfayı Yazdır

4) Real-time Control

Control the load ON/OFF time through setting real-time clock.

5) Intelligent Power Mode

When the battery voltage is lower than "Under Warning Recover Voltage (UWRV

adjustable)", the intelligent power mode is enabled; at this time, the LED current

percentage will be automatically reduced in linear with the voltage drop of battery. When

the battery voltage is lower than "Under Warning Recover Voltage (WRW adjustable)", a

minimum LED current percentage (default 2%, adjustable) will be output. In addition,

when the battery voltage is higher than UWRV, the controller will exit the intelligent

power mode.

NOTE: In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 1Min. delay.

7. Setting Operation

There are three methods that it can realize controller

load modes and parameters through IR function:

1) IR Remote Control—RC10

2) Super Parameter Programmer—FC-01

This method can realize one-key setting operation

which is suitable for bulk quantity products setting or

applied in the projects.

3) Mobile APP+eBox-WIFI&IR-01/02

Real-time monitoring and setting the parameters

Note: Please refer to the user manual of handheld

device

8. Protection

Protection

Conditions

PV Reverse

When the battery is correct

Polarity

connecting, the PV can be reversed.

Battery Reverse

When the PV is not connecting, the

Polarity

battery can be reversed.

Battery Over

The battery voltage reaches to the OVD Stop charging

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Temperature sensor is higher than 65℃ Output is OFF

Battery

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the

Lithium battery

low temperature value

Low Temperature

Temperature sensor is higher than the

(Default 35℃)

low temperature value

Limit current temperature

Lithium battery

limit current in

T1＞T2＞T3＞T4＞T5＞T6

low temperature

Limit current I1＞I2＞I3＞I4＞I5＞I6

10. Technical Specifications

Item

Tracer1305LPLI

Nominal system voltage

8.5～16VDC

Battery input voltage range

Rated charge current★

Rated charge power

50V(Min. Temp.)

Max. PV open circuit voltage

MPP Voltage range

Max. output current

Max. output power

( Max. battery

Output voltage range

voltage+2V)～46V

Load open circuit voltage

Load over voltage protection

Maximum output efficiency

Output current control accuracy

Battery Type

Equalization Voltage

Boost Voltage

Float Voltage

Low Voltage

Reconnect Voltage

Low Voltage Disconnect

Voltage

Boost Charging Voltage

Low Voltage Reconnect

Voltage

Low Voltage

Disconnect Voltage

Self-consumption

Communication

Working environment Tem.

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

★The controller has the limit charge current function, the current can be set via the APP software and RC10.

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

Status

The controller is not

damage

stop discharging

Output is ON

Lithium battery stop

charging

Lithium battery charging

When the temperature is

lower

than

charging current is I1;

when the temperature is

lower

than

charging current is I2;

and so on. However,

when

the

temperature

rises gradually from T4 to

T1, it is performed at I4.

Tracer2606LPLI

12VDC

10A/12V

10A

130W/12V

130W/12V;260W/24V

60V(at minimum operating environment temperature)

45V(25℃)

46V(at 25℃ environment temperature)

( Battery voltage+2V)～36V

3.3A

100W

( Max. battery voltage+2V)～58V

46V

50V

Lead-acid battery: Sealed(default)/Gel/Flooded/User; Lithium battery:LiFePO4/Li-NiCoMn/User

Sealed:14.4V;Gel:14.2V;Flooded:14.6V;User:9-17V(24Vsystem×2)

LiFePO4(4s):14.5V/Li-NiCoMn(3s):12.5V/User:9-17V(24Vsystem×2)

LiFePO4(4s):12.8V/Li-NiCoMn(3s):10.5V/User:9-17V(24Vsystem×2)

LiFePO4(4s):11.1V/Li-NiCoMn(3s):9.3V/User:9-17V(24Vsystem×2)

124×89×30mm

150×93.5×32.7mm

88×76mm

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.52kg

Tel：+86-10-82894896/82894112/+86-752-3889706

Load Short

Circuit

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine falls

on PV modules

properly

No LED indicator

Battery LED

indicator green fast

Flashing

Battery LED

indicator red

Battery LED

indicator red

flashing

Powering on

normally, the load is

off

The dimming

function is invalid

T1,

the

Parameter settings

fail

①When the battery is over discharged, the battery indicator will be red and the load will be

T2,

the

off all the time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV).

In order to judge the system is normal or not, firstly measuring the battery voltage whether

is more than LVRV, if not, restarting the controller to detect the load whether it is normal.

NOTE: The LVRV can be set, but it must pay more attention that it maybe damages

the battery if the LVRV is too low.

Tracer3906LPLI

Tracer5206LPLI

12/24VDC

8.5～32VDC

15A

20A

200W/12V;400W/24V

260W/12V;520W/24V

4.5A

6.6A

130W

200W

58V

63V

96%

≤2%

Sealed:14.6V; Flooded:14.8V;User:9-17V (24Vsystem×2)

Sealed/Gel/Flooded:13.8V;User:9-17V(24Vsystem×2)

Sealed/Gel/Flooded:12.6V;User:9-17V(24Vsystem×2)

Sealed/Gel/Flooded:11.1V;User:9-17V(24Vsystem×2)

≤15mA/12V;≤22mA/24V

IR communication

-40℃～+60℃

IP68(1.5m,72h)

153×105×52.1mm

Φ3.5mm

120×83mm

120×94mm

PV/BAT:12AWG(4mm

LOAD:16AWG(1.5mm

0.71kg

1.18kg

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuit, the output is OFF 10s;

Three short circuit, the output is OFF 15s;

Four short circuit, the output is OFF 20s;

Five short circuit, the output is OFF 25s;

Six short circuit, the output is OFF

Possible reasons

Confirm that PV and battery wire

array disconnection

connections are correct and tight

Measure battery voltage with the

Battery voltage maybe

multi-meter. Min.8.5V can start up

less than 8.5V

the controller

Check if battery voltage is higher

Battery over voltage

than OVD, and disconnect the PV

When the battery voltage is restored

Battery

to or above LVR point (low voltage

①

reconnect voltage), the load will

over discharged

recover

The controller will automatically turn

the system off. But while the

Battery Overheating

temperature decline to be below 50

º C, the controller will resume.

①The connecting

① Check the connecting cable.

wires are error or

② Check the load's mode and

virtually connected

parameters.

②Load mode is not

③The voltage of LED light is not

appropriate.

within the output voltage range of

③This controller does

controller.

not match with the LED

④Check the connecting cables and

light.

LED light.

④Output short circuit.

The controller does not

①Replace the LED light

match with the LED

②Reduce system rated voltage

light source. This

grade and replace the product

product is a step-up

model

voltage control, If input

For example 24V system change to

voltage is lower than

12V system, and replace the

the rated voltage, it is

corresponding controller

not working.

Infrared

Refer to handheld the user device

communication error

manual

Tracer2610LPLI

Tracer3910LPLI

10A

15A

130W/12V;260W/24V

200W/12V;400W/24V

100V(at minimum operating environment temperature)

92V(at 25℃ environment temperature)

( Battery voltage+2V)～72V

3.3A

4.5A

100W

130W

( Max. battery voltage+2V)～80V

80V

100V

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

)

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

)

0.52kg

0.71kg

Any changes without prior notice! Version number：V1.4

Website：www.epever.com

Output is OFF

Clear the fault: Restart

the controller or wait for

one night-day cycle (night

time>3 hours).

Troubleshooting

Tracer5210LPLI

20A

260W/12V;520W/24V

6.6A

200W

153×105×52.1mm

120×94mm

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg