EPH Controls RFRP-HW-OT Kullanım Talimatları - Sayfa 3

Termostat EPH Controls RFRP-HW-OT için çevrimiçi göz atın veya pdf Kullanım Talimatları indirin. EPH Controls RFRP-HW-OT 4 sayfaları. Cylinder thermostat wireless

Sayfayı Yazdır
EPH Controls RFRP-HW-OT Kullanım Talimatları
RFRP-HW-OT
Cylinder Thermostat
13. Adjusting the temperature setpoint
When in Auto or Man mode, press the
temperature setpoint.
Press Ok or after 5 seconds the thermostat will operate to this
temperature.
14. Permanent override
Press the 'MAN' button to enter Manual Mode (Permanent Override).
'MAN' will appear on the screen.
Press the
or
buttons to adjust the temperature setpoint.
Press 'OK
thermostat will operate in this permanent override.
The thermostat will operate in MAN mode until the mode is changed.
To cancel permanent override, press the 'OFF' button or press the
'AUTO' button.
15. Boost function
The thermostat can be boosted for 1, 2 or 3 hours while the thermostat is
operating in all modes except for holiday mode.
Press the 'BOOST' button 1, 2 or 3 times, the time that the boost will be
If you do not press any other button the boost will activate to the time on
the screen after 5 seconds.
Press the 'OK' button or wait for 5 seconds to enter BOOST Mode.
'BOOST TO' will now be displayed on the screen with the time that it is
activated to displayed above this text.
Press the 'BOOST' button again to deactivate the boost.
16. Holiday function
you select .
Press the 'HOL' button, 'HOLIDAY FROM' will appear on screen.
Press the
or
buttons to adjust the day.
Press the
or
buttons to adjust the month. Press the 'OK' button.
Press the
or
buttons to adjust the year.
Press the
or
buttons to adjust the hour.
'HOLIDAY TO' will appear on screen.
Press the
or
buttons to adjust the day.
Press the
or
buttons to adjust the month. Press the 'OK' button.
Press the
or
buttons to adjust the year.
Press the
or
buttons to adjust the hour.
The thermostat will now return to the mode it was in before the Holiday
settings were entered.
To cancel Holiday mode, press the 'HOL' button.
EPH Controls Ireland
[email protected] www.ephcontrols.com
Wireless
or
buttons to adjust the
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Press the 'OK' button.
Page 3 of 4
Operating Instructions
17. To connect the RFRP-HW-OT thermostat to an
RF1A-OT receiver
Please note, If you are installing a CP4-HW-OT, the RFRP-HW-OT thermostat
and the RF1A-OT receiver will have a pre-established RF connection so it is
not necessary to carry out the RF connection process below.
On the RF1A-OT receiver:
Press the
button on the RF1A-OT receiver.
Connect
On the RFRP-HW-OT thermostat:
Press the
button.
Connect
The thermostat will show "nOE" followed by "---"
Once an RF connection has been established the thermostat will show 'r01'
on the LCD screen.
Press the 'OK
The thermostat is now connected to the RF1A-OT receiver.
18. To disconnect the RFRP-HW-OT thermostat from an
RF1A-OT receiver
This can be done from either the thermostat or the receiver.
18.1 On the RFRP-HW-OT thermostat:
Press the
button.
Connect
The thermostat will begin to search through the RF channels.
Press and hold the 'Copy' button for 10 seconds.
'Adr' will appear on the screen of the thermostat.
Press the 'OK' button twice to complete the unpairing process.
The thermostat RFRP-HW-OT is now disconnected from the receiver RF1A-OT.
18.1 On the RF1A-OT receiver:
Connect
Red & green lights if using as a hub receiver.
Press and hold connect for about 10 seconds, the receiver will then stop
The RF connection is now cleared.
19. Backlight mode selection
There are two settings for selection. The factory default setting is AUTO.
OFF
The backlight is permanently OFF.
AUTO
On pressing any button the backlight stays on for 5 seconds.
To adjust the backlight setting, lower the cover on the front of the unit.
Press the 'OK' button for 5 seconds.
Press either the
or
Press the'OK' button.
20. Battery low warning
When the batteries are almost empty, the
the screen.
The batteries must now be replaced or the unit will shut down.
EPH Controls UK
[email protected] www.ephcontrols.co.uk
AUTO
buttons to select the OFF or AUTO mode.
symbol will appear on
20221005_RFRP-HW-OT_OpIns_PK