ARC Audio MOTO 600.4 Kullanıcı El Kitabı - Sayfa 5
Amplifikatör ARC Audio MOTO 600.4 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. ARC Audio MOTO 600.4 12 sayfaları. 4 channel motocycle and off-road amplifier
Sayfayı Yazdır
Remote Status Display
MOTO 600.4
The
is equipped with a Remote Status Display LED that can be mounted in a visible location near the
amplifier. By simply plugging in the Status LED you will have a visible indicator that matches the function of the
Power/Protect light on the amplifier. You can use this to determine if the amplifier is on or off or if the amp is in protection
and, if so, what protection fault code is displayed.
The Remote Status Display comes with approximately
18" of wire however this can easily be extended to
almost any practical length.
Ohm Load Matching
This amplifier is equipped with a unique impedance matching system that allows you to mix a wide range of Ohm loads
and still achieve full power. This can be done independently on the front and rear channels.
2Ω Stereo/4Ω Bridged
Any speaker or combination of speakers with a total combine Ohm load between 2 and 4 Ohms (not lower then 2 Ohms)
must use position. Bridged loads down to 4 Ohm must use this position. The amplifier will make full power at 2 Ohms
Stereo (4 Ohms bridged). Note: you can use any Ohm load above 2 Ohms in this position however power output will drop as the
impedance increases.
4Ω Stereo
Any speaker or combination of speakers with a total
combine Ohm load over 4 Ohms can use position. The
amplifier will make full power at 4 Ohms stereo (8 Ohms
bridged).
WARNING: This amplifier will not operate and could be
damaged if used in the wrong configuration. At no time
can it be operated below 2 Ohms stereo or 4 Ohms
bridged.
Speaker outputs
This amplifier is a multi channel amplifier design. Meaning it has more than one channel of speaker outputs. It is
equipped with a removable plug style terminal for speaker wire connections up to 14 AWG. Make this connection
carefully and neatly. Strip your wire back 5/16" and twist the exposed leads and insert them into the block terminal while
being careful that there is no loose or frayed strands of wire.
Tighten the standard head screw down on the terminal until
the wire is tightly secured in place. If the wires ever come in
contact with each other the amplifier will go into protection.
Know your total ohm load before you make any connec-
tions.
Strip Speaker Wire
TURN ON
5
/
16 "
8MM
CH1
CH3
PROTECT
TURN ON
CH2
CH4
CH1
POWER
PROTECT
USE 2Ω ONLY
LOAD SWITCH MUST BE SET TO 2Ω WHEN BRIDGED
CH1
POWER
PROTECT
TURN ON
USE 2Ω ONLY
4
CH2
CH
CH1
POWER
4Ω STEREO
2Ω STEREO
4Ω BRIDGED
CH 1-2
USE 2Ω ONLY
LOAD
SELECT
CH2
CH3
4Ω STEREO
2Ω STEREO
4Ω BRIDGED
CH 1-2
USE 2Ω
ONLY
LOAD
SELECT
CH2
CH3
4Ω STEREO
2Ω STEREO
4Ω BRIDGED
CH 1-2
USE 2Ω
LOAD
SELECT
LOAD SWITCH MUST BE SET TO 2Ω WHEN BRIDGED
CH4
4Ω STEREO
2Ω STEREO
4Ω BRIDGED
CH 3-4
LOAD
SELECT
CH4
4Ω STEREO
2Ω STEREO
4Ω BRIDGED
CH 3-4
ONLY
LOAD
SELECT
TOP