ABB ACS550 Series Hızlı Başlangıç Kılavuzu

Kontrolör ABB ACS550 Series için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. ABB ACS550 Series 2 sayfaları. Drive it low voltage ac drives 150...550 hp
Ayrıca ABB ACS550 Series için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Kullanıcı Kılavuzu (14 sayfalar), Kurulum Ek Kılavuzu (16 sayfalar)

Sayfayı Yazdır

ACS550

Quick Start Guide

ACS550-01 Drives (0.75...160 kW),

IP21 / UL Type 1 Enclosure

Overview

The installation of the ACS550 adjustable

speed AC drive follows the outline below.

PREPARE for installation

PREPARE mounting location

REMOVE the front cover

MOUNT the drive

INSTALL wiring

CHECK installation

REINSTALL the cover

APPLY power

START-UP

Application

This guide provides a quick reference for

installing ACS550-01 drives having a standard

enclosure.

Note: This guide does not provide detailed

installation, safety or operational

instructions. See ACS550 User's Manual for

complete information.

Prepare for installation

WARNING! The ACS550 should ONLY be

installed by a qualified electrician.

Unpack the drive

Note: Lift the ACS550 by its chassis and not by its

cover.

1. Unpack the drive.

2. Check for any damage.

3. Check the contents against the order / shipping

label.

Check

• Motor compatibility – Motor type, nominal

current, frequency and voltage range must

match drive specifications.

• Suitable environment – Drive requires heated,

indoor controlled environment that is suitable

for the selected enclosure.

• Wiring – Follow local codes for wiring, circuit

protection and EMC requirements.

Refer to User's Manual and confirm that all

preparations are complete.

Drive identification

ACS550-01-08A8-4

3~ 380...480 V

I2N/ I2hd 8.8/6.9 A

Serno

*2030700001*

PN/Phd

4.0/3.0 kW

Use the following chart to interpret the type

code found on the drive label.

ACS550-01-08A8-4+J404+...

AC, Standard Drive – 550 series

Construction (region specific)

01 = Setup/parts for IEC install./compliance

U1 = Setup/parts for US install./compliance

Output current rating

See Ratings in User's Manual for details

Voltage rating

2 = 208...240 V AC

4 = 380...480 V AC

6 = 500...600 V AC

Options

Examples of options:

No specification = IP21 / UL type 1

B055 = IP54 / UL type 12

UL type 12 is not available for type

ACS550-01-290A-4.

0J400 = No control panel

J404 = ACS-CP-C Basic Control Panel

Collect motor data

Collect the following data from the motor

nameplate for later use in the ACS550 startup:

• Voltage __________________________

• Nominal motor current ______________

• Nominal frequency _________________

• Nominal speed ____________________

• Nominal power ____________________

Tools required

Screwdrivers, wire stripper, tape measure,

mounting screws or bolts and drill.

Prepare the mounting location

The drive requires a

smooth, vertical, solid

surface, free from heat and

moisture, with free space for

air flow – 200 mm (8 in)

above and below.

1. Mark the mounting points

using the template.

2. Drill the mounting holes.

X0002

Remove the front cover

1. Remove the

control panel, if

attached.

2. Loosen the

captive screw

at the top.

3. Pull near the

top to remove

the cover.

Mount the drive

1. Position the ACS550 and

use screws or bolts to

securely tighten all four

corners.

Note: Lift the ACS550 by its

metal chassis.

2. Non-English speaking

IP2002

locations: Attach a

warning sticker in the appropriate language

over the existing warning on the top of the

module.

Install the wiring

Wiring power

1. Open the appropriate

knockouts in the gland box.

2. Install the cable clamps for

the power/motor cables.

3. On the input power cable,

strip the sheathing back far

enough to route individual wires.

4. On the motor cable,

strip the sheathing

back far enough to

expose the copper wire

shield so that the

shield can be twisted

into a bundle. Keep the

bundle not longer than

five times its width to minimize noise radiation.

– 360° grounding under the clamp is

recommended for the motor cable to minimize

noise radiation. In this case, remove the

sheathing at the cable clamp.

5. Route both cables through the clamps.

6. Connect the bundle created from the motor

cable shield to the GND terminal.

7. Strip and connect the power/motor wires and

the power ground wire to the drive terminals

using the torques given in the table below. See

Power connections

below or, for more detail,

see User's Manual.

Frame

Tightening torque

size

N·m

lb·ft

R1, R2 1.4

2.5

1.8

5.6; PE: 2 4; PE 1.5

40; PE: 8 30; PE: 6

IP2000

8. Install conduit/gland box and tighten the cable

clamps.

WARNING! To disconnect the internal EMC

filter, remove the screws marked with "

replace the screws marked with " " with the

provided polyamide screws, depending on

the frame size.

System type

R1...R3

EM1 EM3 EM1 EM3 F1 F2

IT system

Corner grounded TN

system

9. Install the cable clamp(s) for

the control cable(s). (Power/

motor cables and clamps

not shown in the figure.)

X0004

IP2001

X0005

", or

R5...R6

- -

X0006