CIOKS 8 Expander Talimatlar - Sayfa 2
Genişletici CIOKS 8 Expander için çevrimiçi göz atın veya pdf Talimatlar indirin. CIOKS 8 Expander 2 sayfaları.
Sayfayı YazdırOverview
Left and right
On the left side you will find the two input/link DC sockets and the three RCA sockets being outlets 1-3 for
powering pedals. On the right there are five RCA sockets being outlets 4-8 also for powering pedals.
Top
CIOKS logo has a red LED placed in the middle of the letter 'O' and this functions as a global status
indicator. For each outlet you have a voltage selector switch and an advanced LED indicator.
Front
The two holes in the front with metric M4 threads are to be used with the GRIP bracket (sold separately)
for mounting to Pedaltrain boards with no drilling required.
Bottom
The four detachable rubber feet are situated on the bottom of the enclosure. On this same surface you will
find 3 holes with metric M4 threads which can be used for mounting of the power supply to a pedalboard.
Getting started
Connect a 24V DC supply voltage to CIOKS 8 power supply from either CIOKS DC7 or other compatible
source. Set the output voltage on a given outlet to either 9, 12, 15 or 18V depending on the needs of the
particular pedal to be powered. Using the right Flex cable type connect your pedal to this outlet. Repeat this
with your remaining pedals.
Advanced LED Monitoring feature
Each isolated outlet has its individual LED status indicator. The indicator is lit in normal operation. The
LED light gets dim when you operate just on the edge of the power limit, regardless of which voltage you
have selected on the outlet. If you overload or short circuit an outlet, the respective LED indicator turns off.
The light intensity of the status LED will be higher when the output voltage is set to a higher value than 9V
being 12, 15 or 18V.
Global status indicator
If the CIOKS 8 power supply is powered from a power source with an output power capability exceeding
56W the red LED inside the O letter in CIOKS logo will be lit regardless of pedal load. If the power source
supplying CIOKS 8 has a power capability of less the 56W the input voltage will when reaching the
adapter's maximum power capability start to sag hence turning the CIOKS 8 global status indicator off.
Pedalboard mounting
General
The most solid way is using the drill template being the product sheet and then drill two diagonally
positioned ø4,5mm or ø5,0mm holes in the pedalboard and fasten CIOKS 8 to it with the two included
screws. Due to CIOKS 8 extremely flat profile and low weight you can use Dual-Lock tape or industrial
Velcro to fasten it below any type of pedalboard. In general for mounting in a rack, pedalboard or other
structure we recommend using two of the five threaded M4 holes (3 in the bottom and 2 in the front) and
matching metric M4 screws. Remember not to penetrate the CIOKS 8 by more than 5mm with the screws
used.
Pedaltrain
For Pedaltrain boards we recommend an easy alternative way of mounting the CIOKS 8 unit by using the
GRIP bracket where no drilling is needed.
Version 1.02
Temple Audio
The three threaded M4 holes in the bottom of CIOKS 8 are aligned with the grid of Templeboards and
allow for very easy mounting on top or below any Temple Audio pedalboard with the included 2 screws.
We recommend using the two holes positioned diagonally. If you want to make a distance between the
board's surface and the CIOKS 8 to allow space for the Temple Audio finger screws you should get a set
of three 8mm hex stand-offs with matching screws (order no. 4HEX) and then use these with all three
threaded holes in the bottom of the power supply.
Included accessories
Flex cables
CIOKS offers a wide selection of different Flex cable types for connection your pedals to the power
supply. Below you see a list of the included Flex cables with your unit:
•
Standard Flex type 1 – black with 5,5/2,1mm centre negative DC plug
•
Standard Flex type 2 – red with 5,5/2,1mm centre positive DC plug
•
Standard Flex type 4 – green with 5,5/2,5mm centre positive DC plug
•
Standard Flex type 5 – black with tip positive 3,5mm Jack plug
•
Split Flex type 1 – black with two 5,5/2,1mm centre negative DC plugs
•
3-way daisy chain Flex type 1 – black with three 5,5/2,1mm centre negative DC plugs x1
Split Flex should be used if you would like to power two pedals with the same voltage using only one
outlet. In the same manner you should use the 3-way daisy chain if you wish to power three pedals of one
outlet. For further information about Flex cables please have a look at the included Flex cable selection
guide or visit CIOKS web site.
DC Link cable
A DC Link cable in 50cm length is included and should be used to connect CIOKS 8 power supply to
CIOKS DC7 power supply's 24V DC outlet. You can also use this cable to connect and power CIOKS 8
of another compatible 24V DC source.
Mounting hardware
We have included all the needed mounting hardware to mount the power supply on top or underneath a
Pedaltrain or a Temple Audio pedalboard. You can of course also attach it to other types of pedalboards.
CIOKS 8 output power capability
When CIOKS 8 is powered of the 24V DC outlet on CIOKS DC7 power supply which we recommend
you'll have a total of 42W for powering pedals of the 15 outlets. There'll be no difference in output
power per outlet whether you use an outlet on CIOKS 8 or the DC7 as they will be sharing the same
source. You can also power your CIOKS 8 power supply of another regulated 24V DC source just be sure
to get the correct polarity and plug type.
Multiple CIOKS 8 or adding a CIOKS 4
If you wish to use two CIOKS 8 power supplies in one rig one of the input/link sockets should be used to
supply power to CIOKS 8 and then the second input/link socket should be used to power the second
CIOKS 8 power supply. In this way you'll be adding 8 additional isolated outlets to your power system.
The same can be done with CIOKS 4 where 4 isolated outlets will be added. Look in the included Flex
and DC Link cable selection guide for which cables to use.
April 2020
Version 1.02
x7
x1
x1
x1
x1
April 2020